Instructables
Picture of Make a Center Finder
Make a precision center finder from scrap materials.

Recently egbertfitzwilly posted an Instructable on Finding the Center of a Circle. WirelessMonk posted a link to a machined steel center finder. Rimar mentioned making one. I decided to try making one that would be very precise.
 
Remove these adsRemove these ads by Signing Up

Step 1: Materials

Picture of Materials
I had a steel bracket left over from something. I also had a piece of wood with good straight edges. In addition I used a little wood glue and a couple of short screws.

Step 2: Cut the wood at an angle

Picture of Cut the wood at an angle
I cut a 45 degree angle across the piece of wood. By cutting it as shown I needed to make only one angle cut for two pieces.

Step 3: The second wood cut

Picture of The second wood cut
Lay the free piece over the main piece of stock. Mark and cut for the second piece.

Step 4: Flatten the steel

Picture of Flatten the steel
My scrap piece of steel needed to be flattened. I began by squeezing it with my vise.

Step 5: Pound it flat

Picture of Pound it flat
The vise did not do all that was necessary to flatten the steel. Use a ball peen hammer on a flat surface. Pound from both sides to make it as flat as possible.

Step 6: Glue the wood pieces

Picture of Glue the wood pieces
Smear wood glue on the facing edges of the wood pieces.

Step 7: Clamp while drying

Picture of Clamp while drying
Clamp the wood pieces to a flat surface. A piece of paper from the newspaper or the phone book keeps the glue from sticking to the flat surface. I placed the flat piece of steel under one of the pieces of wood before clamping to lift it so there would be a raised edge at the joint that I could use to align the piece of steel when fastening it to the wood. The edge of the steel will need to bisect exactly the angle formed by the two pieces of wood. The glue line is on the line that bisects the angle. While the glue is not yet hardened scrape away the excess glue with a chisel so the raised edge is clean and sharp.

Step 8: Attach the steel

Picture of Attach the steel
When the glue is dry, press the piece of steel against the raised edge. Clamp the steel to the wood so it does not move while you drill and attach the steel to the wood with screws.
1-40 of 81Next »
ant0ny1 year ago
Great idea! Does not even matter what angle of the cut - 30, 40 or 47,358 degree! :) Still glued line will divide the angle in half.
Thank you!
Phil B (author)  ant0ny1 year ago
Exactly. And, making a diagonal slice across a straight piece automatically make the angle on the cut pieces equal.
ynze1 year ago
Very smart! I bumped into the problem of finding the center of round wood recently. I just noticed this I'ble (first picture), and.... Owwwwwww, of course, that's the way!

Thanks!

Y.
Phil B (author)  ynze1 year ago
Thank you for looking. I am glad it is helpful to you. It was fun to develop and I use mine more than I thought I would.
Wow. Weird that this landed in my comments, but glad it did lol. I could use such a thing :)
grbennet1 year ago
Thank you very much for this simple method.
Phil B (author)  grbennet1 year ago
I hope it helps you. Thank you for your comment.
Learndy5 years ago
Can we extend this mechanism somehow to find the center axis of a sphere, of a ball?

Application: Find a center axis of a table tennis ball to make it a cheap wheel for a small robot.
--
Airspace V - international hangar flying!
http://www.airspace-v.com/ggadgets for tools & toys
Phil B (author)  Learndy5 years ago
Here is an idea for finding the center of a sphere, like a table tennis ball. For the sake of illustration, your table tennis ball is red in color. Cut a collar of PVC that is just a little smaller in diameter than the table tennis ball. The PVC collar is shown in cutaway and is gray in color. Cut it to length so the top of the ball is roughly even with the top of the ball when the collar is resting on the ball. Use the center finder to mark the center from a couple of directions. You will need to turn the table tennis ball over to mark the extension of the axis. Do that by making a circle on a piece of paper, the diameter of which is the same as the PVC collar. Mark the center of the circle. Align the center you marked on the ball with the dot on the paper. Support the ball from several sides so the center do on the ball remains squarely on the center dot marked on the paper. Place the PVC collar on top of the ball so it is level. Without moving anything, use the center finder to locate the extension of the axis.
sphere.JPG
Col_uk Phil B2 years ago
Hi Phil
Thanks for the instructable, it came in very useful.
For a sphere, i found it easier to make a center finder the same depth as the ball diameter and put steel on both ends. That allows you to mark both poles at the same time.

best regards
Phil B (author)  Col_uk2 years ago
Very clever. Thanks for your reply.
Phil B (author)  Phil B5 years ago
Oops! "Cut it to length so the top of the ball is roughly even with the top of the ball when the collar is resting on the ball." should read, "Cut it to length so the top of the collar is roughly even with the top of the ball when the collar is resting on the ball."
Use the center finder to draw a first "equator" line. Turn the ball and use the center finder to draw a "meridian" line.
The two intersections (the "poles") give you the axe for an axle.
streetrod52 years ago
Phil, this is something I've needed for years, but didn't know it existed! I've been "finding" centers by... well, not the most accurate way. Thank you!
Phil B (author)  streetrod52 years ago
Thank you for looking and for your comment. I am glad to have solved a problem for you.
bettertimes3 years ago
If you would enjoy reading "The Boy Mechanic: Volume 1 by Popular Mechanics Co. " here is the down load link
http://library.beau.org/gutenberg/1/2/6/5/12655/12655-pdf.pdf
this is a copy from the Deridder, Louisiana Library. enjoy
Phil B (author)  bettertimes3 years ago
I did download it and have looked at some of it. When I was growing up our public library had a couple of books by Alfred P. Morgan. One was on electricity. One was on all sorts of mechanical devices. I remember a small steam engine with bell cranks to operate sliding valves. The projects were marvelous, but always required tools and materials I did not have available. Thanks.
DoDo7293 years ago
Wow, so simple but works incredible. Solved one of my problems. Thanks for your post. Love this site.
Phil B (author)  DoDo7293 years ago
I am very pleased you found it and can use it. Instructables is a great place to share useful things. Thank you for looking.
nmh0105 Phil B3 years ago
Simple but yet great use... i could not follow you please help
Phil B (author)  nmh01053 years ago
Can you say what exactly you did not understand?
Creativeman3 years ago
I just found this, will definitely make one! Will post picture when done. Thanks for the idea/concept.
Phil B (author)  Creativeman3 years ago
Thank you. You may even find a way to improve on it.
wmarin Phil B3 years ago
You are still my hero !. Thanks
Phil B (author)  wmarin3 years ago
Thank you.
pgcagdol3 years ago
thanks great idea and just when i needed it
Phil B (author)  pgcagdol3 years ago
Thank you. I try to post useful things.
nice job..thanks..
Phil B (author)  zulhanifarifin4 years ago
Thanks. I hope it is useful to you.
Chadworkz4 years ago
You know, it's always the simplest things that are the best, and this just proved that point...excellent job, Phil! ;)
Phil B (author)  Chadworkz4 years ago
Thank you.  Unfortunately, it usually takes me a few attempts before I come to a really simple version of an idea.
una mente creativa ... Lo seplice muove il mondo benfatto!!!
Phil B (author)  roberto sirigu4 years ago
Grazie mille!
ignilc4 years ago

The angle doesn't need to be 45 degrees. It can be anything. As long as the angles on both pieces of wood are the same it will work well.

Phil B (author)  ignilc4 years ago
You are quite correct.  Thank you for your comment and thank you for looking at this.
This is very helpful :) thanks
Phil B (author)  mcanderson765 years ago
Thanks.
This is one of those things that makes me think, why didn't I thinkof that?! A straight forward solution to an annoying problem. Nice guide.
Phil B (author)  manuelle_override5 years ago
Thank you. I see you joined Instructables less than a week ago. Welcome. How did you happen to find my center finder already? Speaking of simple solutions to annoying problems, you might be interested in a recent Instructable I did. Search for Garmin Vehicle Power Cable. Even if you do not have a Garmin with a 12 VDC power cable, you might be able to use the basic idea on something else.
5* Now I just need to summon the energy to get back to my projects...:)
1-40 of 81Next »