Instructables

Make a Vacuum Former Box $30

Featured
Picture of Make a Vacuum Former Box $30
This Instructables will show you how to make a very cool Vacuum Former box for just about $30!
 
Remove these adsRemove these ads by Signing Up

Step 1: Materials

Picture of Materials
Pegboard
1/2" Plywood
2x4
Duct Tape
.02 Polystyrene
Oven
Shop Vac
2x2

Step 2: Make the Frame

Picture of Make the Frame
To start out make a square frame out of the 2x4, mine was 22"x 24"

Step 3: Make Vacuum Former Plate

Picture of Make Vacuum Former Plate
IMG_2384.jpg
IMG_2386.jpg
Now take your 1/2" Plywood and cut out a square 24"x26" next cut two 3"x 24" pieces and two 3"x 26 pieces. Take the 2x2 and cut 4 2.5" pieces.  take one of the side pieces and drill a large hole into it mine was an inch and a half but could have been larger. This is where the shop vac hose will connect to. Then cut out piece of pegboard the same size as your base, or 24"x26".

Step 4: Assembly

Picture of Assembly
IMG_2387.jpg
Take the 4 2x2's and screw them from the bottom of the 24"x26" base then take the four 1/2" sides and screw them on.Take the pegboard and screw it onto the 2x2s. There now you have all the pieces required.Then take the shop vac hose and push it into the hole and secure it. I used duct tape but am currently working on a better solution.

Step 5: Plastic

I ordered mine from http://www.usplastic.com/catalog/item.aspx?sku=43330&catid=715 the actual plastic is cheap but shipping is an arm and a leg. If you can find polystyrene anywhere else .02 to .04 inches it will do just fine. Take the plastic and cut out a square that is the size of the 2x2 frame then staple it on nice and tight.
greyfox234 (author) 1 year ago
Hey guys I wanted to let you know about my blog. So here it its:
http://manbehindthecanon3.blogspot.com/
the only issue that I have w/ it is the fact that pegboard isn't all that stable, it tends to break under pressure, & w/ a vacuuformer table there will be lots of pressure.
I have done almost this exact set up. Though mind had the oven built onto it with a frame to flip the plastic onto the oven and back to the work space.

To overcome the strength issue with the pegboard you can place spacers in the blank spaces between holes. Putting a hanfull of spacers works great.
I've seen a similar project done but instead of using pegboard for the vacuum table, the builder used a piece of MDF and drilled the holes by hand. He said it only took about 10 minutes but the thicker material was more stable and less likely to buckle under the force of the vacuum.

One could also take three sheets of pegboard, glue and laminate them but you'd have to be careful not to plug the holes with glue. By the time you cleaned out all the holes, you might have been better off just using the MDF.

Still, I now REALLY want to build a vacuum former.
I was thinking the same thing. I'm also designing a semi automated vacuformer for myself. I'm planning on using MDF for the framework & stronger woods for the vertical frames.
frikkie1 year ago
Sorry if I ask a stupid question but like my one teacher used to say 'He that does not ask a question is dum' but anyway what is the use of the wooden box? I mean like what does it do? I dont understand. I also want to mould stuff. But is the box that you made just to put the mold on while in the oven?
greyfox234 (author)  frikkie1 year ago
Yes it is, I stapled the plastic to it and then put that piece in the oven. Then I placed the heated up plastic over the mold and turned on the shop vac.
Very cool! I like that the project is inexpensive and explained very well. That mask is very nice too.