Step 5: Remote Battery Packs

Shown is just one AA battery but if you cut the piece of inner tube wider you can parallel several batteries for more amperage and amp-hours.

(Hint: Use larger tubes or rubber bands for C and D cells)

<p>hey Danny, I just recently ordered an adapter from batsub.com site that was recommended below. It works great! My wife uses it for our baby&rsquo;s crib mobile and she said it was pretty easy to set up.</p>
<p>Can you do one for me, or where can I buy one. I need get rid of those two AAA batteries of my keyboard. I find this idea excellent. Great!!</p>
<p>This is great. I needed to make the AA battery accessible from my battery operated clock so I didn't have to take off the clock face to change the battery. Now the battery is located in a holder outside the clock movement. The dowel and thumb tack approach is just what I needed for the old battery connector.</p>
Check out the new device at www.batsub.com; It's an adapter that'll help you with battery substituting. I think it's a step in the right direction.
yes dowel is what i used
I've done the exact same thing some years ago to power my (now sold...) Sony MD player. I was eating so much power when transfering music to md that I've created a AA cell just like you did here... 1wood dowel with thumbtacks Nice instructable
Thanks. It was a kind of fun project knowing I could beat the man. :-) The need to prevent a shutdown in the middle of a shot, even with less power hungry chips offered in newer cameras, by using an external power pack is just too critical to pass up.
You might be surprised with the newer cameras. I was extremely upset when I saw how small the battery is for my newest camera. But I have completely loaded and downloaded the memory once or even twice over without even losing a bar. I only put it on the charger after it gets a good workout and is down at least a bar or two... and that's not often.
It's mainly other devices without a power connector that inspired this Instructable. For 9 volts batteries I've always just snapped on a 9 volt connector wired to an external power supply. With AA or AAA you can insert a piece of double sided circuit board between the battery and the battery terminal instead of using thumbtacks and a piece of dowel but I wanted to be able to put my discharged batteries into the charger and still be able to use the camera. The newer cameras almost make throwing the older cameras away a no brainer.
My method would be to glue a 3 pin section of female pin header onto the outside of the camera, next to the battery holder. Then solder 30 AWG kynar wire directly to the battery terminals, connecting them to the port (middle pin positive, outer pins negative). This would create a nonproprietary power plug. Then use clear packing tape to hold the wires down to the battery case. It sounds hard, but it's probably easier than making fake AA batteries. I've done this many times. BTW, you only have to solder two wires, not four. Rarely, some test equipment might run from a +- 1.5V supply, but your typical device only uses the 3 volts in series; two of the leads in that battery clip are actually higly likely to be connected to each other (and to nothing else) and can be ignored, altogether. Actually, the way you wired it, you should be careful to not hook them up to the same 1.5V power source, as you will probably just short the power supply. If the camera has an easy to open plastic case, as yours appears to have, you can even solder your wires directly to the pcb. Then you could either make a tiny hole through which to route the wires, or you may even find enough space to cut a slot for the port's face and mount the entire port internally. Nice instructable!
"contacks" - i like it. make sure you have the right amperage though. portable devices pull power out of batteries and wall wart transformers at whatever rate the device needs. batteries supply the device with pretty much any amount of amps needed, because they are drawn out of the batteries. in a wall wart transformer, this is not always the case. if the listed amperage is too high, that's fine, the device will only pull what it needs from the wall unit. if the listed amperage on the wall wart is too low, it will not have sufficient power and could lead to device malfunction.
Thanks for the tip! Device load is a very important consideration. I am glad you brought it up. Digital cameras are one of the heaviest loads a battery or a wall wort can have and one of the reasons so much effort has been put into making chips that have low power consumption. An Energizer lithium AA cell is rated at 2 amps continuous and 3 amps pulsed (2 sec on, 8 sec off). That's 3 watts continuous and 4.5 watts pulsed. Most alkalines are rated at 1 amp or less which would be 1.5 watts. If the load is too great for the power supply then the power supply will heat up and so will its leads, if they match the power supply's capacity. Low current is usually not a problem for the device since it is treated like a battery going dead. Too much of a load will cause the voltage to drop which will in turn activate the device's shutdown circuitry. To prevent this a larger regulator or a bigger wall wort up to 3 amps capacity can be used. ...and you are right, a 5 amp regulator would not hurt either.
fo sho
I just made one a few weeks ago i was going to post it you beat me to it . what else do ya got?
Even if it is exactly the same there is no harm in posting whatever you've got. I have hundreds of things scheduled but to do one right takes a lot of work so I have to be really enthused about it before it gets the go ahead. Do you know how to make a hydrometer? We have been waiting and waiting for someone to do an Instructable on that. :-)
Awesome! I'll have to do this some time
Intelligent idea. Great pictures, great detail, just great everything. This is truly just a great Instructable. :-)
I'm glad you like it. It was kind of fun. In the past I've always just tapped into the battery circuit and added the missing connector myself but in my new camera there is just no room for even the smallest connector to be added.
Great! The use of the wood dowel and the pins is a great idea! Maybe with a thinner wire... A+++
Yeah, these wires came from the wall worts but in case of wires being too thick you can use a hack saw blade to cut a channel in the dowel so the wires can be recessed. For thinner wires, bare wires could be sealed with glue or epoxy inside separate grooves. I was thinking of using some telephone service wire, except that it is solid.

About This Instructable




More by thinkahead:A cubical pocket stove How to "Salt Out" How to caramelize store bought cookies - yum! 
Add instructable to: