Picture of Make a silencer for your Nerf Longshot
Step 6.JPG
I am going to show you how to make an awesome looking silencer for your NERF Longshot!
Remove these adsRemove these ads by Signing Up

Step 1: Supplies

Picture of Supplies
Step 4.JPG
Okay. You are going to need a few supplies:

-The barrel from your Long Shot's front gun
-The barrel connector ring
-A 15" long piece of 1/2" PVC
-A new roll of 2" wide Electrical Tape (color does not matter)
-6 couplings with a diameter of 7/8" and a length of 1 7/8"
-Hot glue gun

Step 2: Wrap the Barrel

Picture of Wrap the Barrel
Now that you have the supplies, wrap the Electrical Tape 1 TIME around the barrel. Do not allow the tape to overlap. Start on the side of the barrel that has the bigger end to it. So after taping the whole barrel like this, you should have something similar to the picture below.

Step 3: Slide the couplings over the taped barrel

Now, slide the 6 couplings all the way to the end 1 at a time. After they are all pushed down as far as they will go, wrap some Electrical Tape around them so that they are all connected.

Step 4: Tape, tape, and more tape.

Picture of Tape, tape, and more tape.
Step 3 (2).JPG
Now you are going to need to wrap the electrical tape around the back two couplings and the front two couplings as tight as possible. You will wrap the tape so that it is 2/8" tall. (See pictures below)

Step 5: Slide the barrel into the PVC pipe

Now that you have taped the barrel, you will need to slide it into the PVC so that you are pushing the fat end of the barrel. NOTE: You will need strength and patience. Leave the fat end of the barrel sticking out about 2/8" from the PVC.

Step 6: Use pliers to break off...

Picture of Use pliers to break off...
Now, use pliers to break off the smaller tab from the orange thing that slides onto the connector of the Long Shot's barrel. You will also have to trim the top of the ring a little bit so that the PVC will fit flush against it.
Take the stock off and its a nerf g11
benduy3 years ago
anyone noticed the longshots look like a g11?
objection!5 years ago
Would this work on a Recon CS-6? I can't find damn longshots ANYWHERE IN THE ENTIRE COUNTRY (of Australia, natch). GNGNG. This would look better if it was black, though. But that's just my opinion.
hey dude, im in aus and i got my longshot from k-mart on special for 38 buks! its awsome! k-mart has a good range of nerf guns right now in the huge toy sale.
big w also has them as well as kmart
I bought my longshot off, try there!
ya it should work on the recon
Batryn4 years ago
This wouldn't silence it. You're much better off opening it, and padding the moving parts with foam, since it's not the air, but the springs that makes the sound.
JOE19034 years ago
In the UK this makes the Longshot illegal :P
So unfortunately I can't try this without risking a hefty sentence for posession of a firearm. Dammit >.<
Austin Rice (author)  JOE19034 years ago
What makes this illegal? It does not silence the rifle at all. It is as if you have the front pistol attached to it.
the only way to silence a longshot would be to put some sort of padding inside it.
ldkv4 years ago
You can still hear the sound when you shoot is but it makes it look cool. p.s. first to comment. ha ha
It does make it shoot farther a little bit
MAVREV135 years ago
does it make the ls any more silent or is it just for looks.
The photographic quality is somewhat inferior to what I am expecting sorry Im so high-standard-izeded. :)
tron1o75 years ago
Are the couplings you are talking about the 2 pieces of PVC pipe in the picture?
Austin Rice (author)  tron1o75 years ago
Yes. If you go to a hardware store, they will know them as couplings. I do not suggest you use PVC pipe, because the coupling has a small ridge on the inside of it, which allows 2 different PVC pipes to be connected evenly throughout the coupling.
bleachfeak5 years ago
what happened to the but?
Austin Rice (author)  bleachfeak5 years ago
Oh...I took these pictures when I was in the middle of doing mods to the inside of the gun ;). You want to try taking the screws out/ putting them in the least amount of times as you possibly can. The threads on this gun strip fairly quickly. Same with the screw heads.
i found that out kinda quick,lol
(seabear)5 years ago
do stefans work with tha longshot
when I get the longshot I'm gonna do this, oh and you will have the same barrel length for less weight