Make your own Nerf darts. AKA: Stefans.

Step 4 Go nerf

Now, take your newly made foam of destruction, put it into a nerf gun, and go shoot your brother......errrrr a target

The first pic below is the 100 that i made.... the 3rd pic is the welt they leave.

have fun and be safe! ALWAYS where eye protection when using these darts, they can seriously hurt you. (note the welt in the third pic.)

Comments

[JasonMyers]

God! Can I get some of the foam at Menards, Farm & Fleet, or Wal Mart?

[basher345]

Walmart may have some.

what's Menards and Farm & Fleet?

[ilees]

Trolololololololol

[Monkeyboy13]

Mine keep pinwheeling when i shoot them. What did i do wrong? I've been trying different weights and it ain't doing much

[Dobbo151]

it might be that you've not put the weights close enough to the center of the tip of the dart, or possibly the foam has not straightened properly

[eman414]

soooooo these wont work with a maverick unless you take the center pole thingy in the chambers?

[geodez]

use in the nerf vulcan ebf-25.

[DIY and STUFF]

do these work for long shot, recon, cs-35 gun

[pocholox8]

um.. why dont u try it urself first?

[The_Lost_Carrot]

you will have to mod the clip in order for the stefans to fit which is quite easy to do but not on the raider drum mag

[hdn_5]

Any particular kind of BB's you use?

[moundskills]

you should probably paint those a bright color so you can find them easier

[A.C.E.]

hey twisted, how far do these shoot on a modded longshot? PS.. i am looking to mod my cs6, but i cant find anywhere that doesnt use an air compressor : P did you use a guide when you modded yours? can you give me a link to a good tut? thanks

[emuostrich]

1/2 inch stefans fit in the standard, stock, ar removed, barrels right? And for megas, you need pvc...

[fazizal]

i doubt it makes welts you can make it extreamly deadly but it really depends on the gun(maverick rev 6 or long shot)?

[colton200456]

maverick thx im thinking of getting the nerf vulcan cs-6 then could upgrade my maverick do u think that is a good idea

[~Shadow~]

tkdswimmer. no they don't work without a modded nerf gun. if you notice, average darts have a hole down the back of them, so they fit into the rod that is down the barrel of the gun. without taking apart the gun, and breaking off that rod, the stefan's won't fit down the barrel. by the way, dismantling guns aren't as hard as it seems. I've dismantled my Maverick rev6 without doing harm the actual gun. Fires fine, and a lot more effective with the mod. I haven't made these stefans yet, but I can tell these are going to be good

[littlemog92]

i make my stefans full size and with the complete hole in the back you take a screw driver heat it with fire and make a hole

[Kingbow111]

I don't get how to take out the rod thingy... first i have to take out the metal bar inside the rev6 magizine, but I CANT TAKE IT OFF FOR ALL THE LEVERAGE I HAVE!!! help please?

[Ojsmudge]

use a claw headed hammer to get it off

[The Farfignugen]

use a long skiny scissors and cut them out

[killaskilz]

take tho chamber completley apart

[skotman1974]

what i did was take a small screwdriver or punch about the size of the hole on the orange round piece put the cartridge on a table and use the screwdriver/punch with a hammer to tap the rod out worked perfectly just don't hit too hard.

[nerfer192]

is pic 2 your place after a nerf war?

[tkdswimmer]

do they work without modded nerf gun?

[Iferit_777]

Its really hard for me to find the fbr i cant find it at home depot or ace.i have a modded maverick rev-6(no air restrictors) just started into nerfs a week ago.so it really makes welts? and where did you get the black fbr?