Instructables
Picture of 40 More Handy Tricks
humbird02.jpg
humbird03.jpg
Continues the saga begun at Fifty Handy Tricks.

http://www.instructables.com/id/Handy_Tricks_8_Island_Handy_Tricks/

To see even more of them check out Handy Tricks 8: Island Handy Tricks
and Yet More Handy Tricks
and Australian Handy Tricks
and Guatemalan Handy Tricks
and Handy Tricks Volume Six!

For a bunch of things that didn't work, check out How Not To.

First Trick: "Instant Hummingbird Food

My mom makes her own hummingbird food. It's really easy. She pours white sugar into the feeder bottle til it's 1/3 full, then fills it the rest of the way with warm water. Then she shakes it up and hangs it outside. Pretty simple and the hummingbirds love it.. I'd worry about where they get their vitamins, except they're always rushing off somewhere, and don't seem to try to get all they're day's food from the feeder.

You could make your own hummingbird feeder without any trouble. It's just an inverted bottle stuck into a covered dish with some holes in it. The "flowers" don't have to be there, a red dish cover works fine. My mom's other feeder lost its flowers and the birds don't seem to care. That's the unit in the third picture.
 
Remove these adsRemove these ads by Signing Up

Step 1: Instant Bicycle Rear Cargo Rack

Picture of Instant Bicycle Rear Cargo Rack
rack01.jpg
My pal Corwin Hardham made this really apt bike rack by cutting the rear part off of one bike frame and welding it onto another. Very slick. Once you see it it seems obvious.

I don't usually do instructables that involve welding because someone might not have a welder.
But this rack is so cute I couldn't resist.
If you don't have a welder, flatten the ends of the tubes with a hammer, drill holes in them, and bolt them to your bike frame.

1-40 of 163Next »
coolniss
demaytri1 year ago
i've done this since the first time i learned to play guitar (which about 12 years ago), my sister taught me this trick. it works pretty nicely.
would this work on regular clothes? i was thinking about waterproofing a hat and this seems a good idea.. and what about what crache said? is the oil combustable near heat or is it just the boiled oil? thanks
nice idea. i hate the fact that there isnt a safety switch on dremel just in case itts dropped
The spray is to kill any mosquitoes so you don't get malaria. Actually, people who work near int'l airports are more likely to get malaria that anybody else.
katala2 years ago
I did the same thing, except I use the Lutron Credenza plug in dimmer. You don't have to cut the power cord, just plug the Dremel into the Lutron, and you're off and running, $10 at Home Depot or Lowes. Note, triac based dimmers work with universal brushed motors, despite the Lutron box saying not to be used with motors; that's the same type of electronics used inside the variable speed Demels.
candilee472 years ago
Re: the bird-feeder. My brother used red food colouring and this seemed to attract them in the 10s!!!
I have been collecting marbles from spray paint cans ever since I was a kid. I currently have 300ish spray paint can marbles and I had about 100 stolen from my car years ago; I suspect I have personally opened over 400 cans. I can validate many of your comments.

First: Metal balls, usually with a flat spot on opposite sides, come primarily in primers and very small cans. They rust, yes, but only after having been exposed to the air. While in the pressurized can, full of paint which would solidify if it was exposed to air, they are fine.

Second: You normally get only one marble, some cans have two. I have never found a certain brand that always has two.

Third: Yes, they can be dangerous but you can open, semi-safely, a full can. They can fly out of your hand though as they act like a large, angry, directionless, heavy bottle rocket. The can doesn't explode though. It is unnecessary to spray out the remaining pressure, but you can if it makes you feel safer.

Lastly (fourth): Yes, they are glass marbles. They seem like marble "seconds" as they are usually not totally spherical and some have grooves in the glass. I have found very few opaque marbles which were not black. Many have bubbles throughout them. Blue is the most prevalent color.

I made a special tool out of a piece of 1.5" angle iron that I use to open the cans and extract the marbles. It is also beneficial to have a pan of paint thinner or stripper to drop the marbles into upon their birth into air as it is awfully hard to remove the paint once it has dried.

On a personal note. It always disturbed me that there were no other people who collected the marbles from spray paint cans. It is nice to see that there are at least a few people with the interest.



knorman42 years ago
Just did this also. Smooth and quiet. I commute by skateboard so it's awesome for me, not sure how it bodes for tricks (I'm new to skating and don't do many tricks yet). Highly recommend trying it out though.
bennyb13 years ago
I just did a pair of high top canvas boots like this, and wonder how long it takes to dry. They're supposed to be waterproof, have felt liners, but figured this wouldn't hurt to try, since I haven't used them in a coiuple of years.
They're on the front porch in the sun, and hope it doesn't take more than a day or two.
Thanks for the idea.
How about a dimmer switch(like step 14) for the speed control?
Nice idea, but dimmer switches (the kind used for house lighting) only work with AC current at a minimum of about 100 V (though they don't care if its 50 Hz or 60 Hz). They're based on an electronic device called a Silicon Controlled Rectifier (SCR), which turns on when the voltage on the control gate reaches some designed-in minimum, and turn off when the voltage on the switched terminals hits zero. Wire up a couple in opposite polarity with a resistor/capacitor circuit to control how much of each half cycle actually gets passed, and you have a light dimmer -- I built one in a college electricity lab in about fifteen minutes, thirty years or so ago.

Unfortunately, it's much harder to build an electronic speed control for DC -- the simplest way is to use a whale of a variable resistor in circuit, but then you have to throw away the waste heat somewhere. The next simplest is to use a DC motor and AC generator (alternator, for instance), with a variac to control the voltage that then gets fed to a rectifier that powers you drive motor. The problem with this is that the motor and generator in the converter have to be about as big as the drive motor, or they burn up. What's actually used in most modern electric vehicles is a "chopper" control -- it's got a huge, well cooled transistor of one sort or another that's turned on and off very rapidly, and the ratio of "on" to "off" is varied to control the motor speed. Small ones are cheap and come on a single chip; big ones are expensive and can be complicated to wire up -- and a go cart like this one is getting into the "large" category.
sdhicks3 years ago
Just the kinda thing I come here to see! Thanks
arpruss3 years ago
While this is great advice for turning AAs to Cs, Ds require more work as they are longer, I think.
yep. you're absolutely correct.
Okay, so my son needed some D batteries for a Hotwheels track thingy. Of course we had none. I got so excited when I remembered that someone pinned this blog. I found the pin on Pinterest and clicked to come to this blog. I them cut up the cardboard, all to no avail. AA batteries are the same height as Cs, but NOT Ds!!
LOL get a job so you can write all warning lables ?
trainables3 years ago
Great use for a dimmer extension cord. Hadn't thought of this.
gpeterson23 years ago
Fair warning - you may feel better that you haven't killed the mouse, but they will come back if you do anything less than take them down the street. And where there's one, there's more, so you're unfortunately probably not going to get rid of your problem. I don't like killing them either, but sometimes it's the only real way to get rid of them.
p. observer3 years ago
this just got featured on lifehacker. Hi guys!
ruashiasim3 years ago
This info is incorrect. mix gas does NOT spoil faster than non-mixed. In fact it might actually last a little longer. Either way ANY fuel intended to be ran in small engines should be less than 3 months old and of premium quality. Old mix fuel that isn't stale (really really foul smelling) can be diluted into a automotive fuel tank and will not hurt anything in your car
Alderin3 years ago
This reminds me of a pickup I saw in South Carolina, major rust, but it used to be a yellow truck. In the back of the cabin in the top was a message scratched into the paint: "This is NOT an abandoned vehicle"

LOL
slaitch3 years ago
I saw several of these stuck together back to back and used as the booths in a restaurant recently. Nifty.
spook663 years ago
The soap also makes the water "wetter" so it squeegees out more easily. Use this for all vinyl decal applications as well
wllmundrwd3 years ago
I did that very thing earlier this year; my brother was amazed and I still don't understand why...
Tim are you from MN?
urtlesquirt3 years ago
Dude, this is elementary in any junior sailing.
I agree totally, after buying Feibings products and using almost a fivers worth of dye just to do a hat, I tried inkjet printer ink, and it actually works better. I can buy it in 1 litre bottles for £9.00 a litre or less, so it works out extremely cheap, (I use CISS systems for all my printers, and an Epson cartridge, instead of costing £3 for pattern, or £6 for original, now equates to 8-17p each!). As an artist I use Rowneys System 3 acrylics, and as these come in 500 ml bottles at about £12, they work out very cheap. As for 'Resolene' finishes etc, I'll just go to my local Dixons painting and decorating supplies and buy acrylic semi-gloss glaze.
great idea! did this with a pickle jar and caught a mouse within 20 minutes!
Jonbloozy3 years ago
Been doing this for years at events when we need to work a cash register or do a lot of writing (while standing). Definitely saves your back.
zombie19744 years ago
I had a friend who said his favorite "riding leathers" weren't leathers at all, but a pair of standard denim farmer overalls that had soaked for a couple of days in the oil pit at his neighborhood garage, and then hung on the line for a week to dry. He said they always looked dirty, but he never got wet and they'd stand up to road rash almost as good as leather.
Plus he got them too big so he could wear them over normal clothes, and they didn't damage his normal clothes (at least not enough that he cared about it).
chuck_294 years ago
i'm sure this is already written, but i'm not going to look,, it's gotta be a glass marble cuz if it was metal, it would rust and probably stick and not stir the paint..
sharlston4 years ago
tim,i was wondering the innertube is it a normal mountain/bmx innetrube or a racing bike?
Pantomime_4 years ago
Any tips on what to do with the 'remains'?
eric m4 years ago
 strange place to splice near the plug.
We silly americans prefer to buy stuff made in china made of nylon with lots of straps, plastic buckels and velcro, when a folded scarf would work?
kawaiipeach4 years ago
i've just discovered that Warnings can be fun LOL
that is cool, is it too oily or does it look dry?
TimAnderson (author)  weaponscollector944 years ago
It's kind of rubbery, it's not oily at all. The cloth rag has a very loose weave and it does leak when you try to use it as a bucket. Use a tighter weave if you want it fully waterproof. Water beads up on it and it does shed water very well.
this is indeed a very handy trick
1-40 of 163Next »