Instructables
Picture of (POP)culture
Garth Britzman 2.jpg
Chris Paulsen 4.JPG
Chris Paulsen 3.jpg
Chris Paulsen 1.JPG
This project used 1,581 recycled soda bottles to create a canopy for shading from the sun.  The project incorporated 3D modeling and scripting software to generate the desired surface created by the bottom of the soda bottles. The project sought to stimulate creative alternatives for recycling and reusing materials.

Each bottle is filled with a small amount of colored water.  The specific color of the water is based on the elevation of the bottle relative to the groundplane. Each bottle is hung from a grid by a unique string length ranging from 6" to 30". 

Basic Materials:

1,581 soda bottles
washers
masons line 1000+ yards
hot glue
masking tape
wood 4x4 and 2x6
wood screws
brackets
food coloring
water
outdoor paint
basic tools
many volunteers!!

Step 1: Digital Fabrication

Picture of Digital Fabrication
Production data.jpg
rhino ba.jpg
I used Rhinoceros, a 3D modeling program to create the surface that the bottom of the bottles form.  From this form, we used Grasshopper (a scripting program) to generate a dataset containing the length of each string corresponding to a coordinate grid system.  For simplicity, we label one direction of the coordinate using numbers, and the second direction using letters. The dataset, in addition to providing the location of the string, provided the color of liquid in each bottle that would hang from each string.

Step 2: Cutting String

Picture of Cutting String
Production data.jpg
For this step, over 20 people volunteered their time throughout about 3 weeks working to prepare each individual string to hang each bottle.  Each string was labeled and cut to a specific length per the length denoted by the table.  A washer was tied to one end of the string so a bottle cap with a hole drilled in it could be hung from the string. This step takes many hours and is rather tedious.  Each individual was given 51 string lengths to cut in one sitting (the number of bottles in one column of the structure).  Doing it with other people makes this step in the process much more enjoyable.

Step 3: Bottle Preparation

Picture of Bottle Preparation
021512_0300.JPG
Collecting all of the bottles was the first major hurdle in this step.  I worked with the campus recycling program at the University of Nebraska to get them.  Volunteers then cut the labels off of each bottle, then we sanitized them by first dumping out all contents, and finally rinsing with a mixture of water and bleach.  We rinsed each bottle before rinsing again in plain water.

Step 4: Structure

Picture of Structure
030312_0008.JPG
030312_0018.JPG
The structure was made from 2x6 timber for the top frame measuring 8' by 12' by 8' high.  The columns were made by 4"x4" wood assembled with wood screws.  Diagonal reinforcements were added at the corners and metal brackets were added at the corners for added structural stability. We found some scrap wood to add additional reinforcements to the corners of the frame. 

We painted the frame white using paint suitable for outdoor conditions.

-These images were taken later in the process however they best demonstrate the construction of the frame.

Step 5: String Grid

Picture of String Grid
We added screws to the top of the structure at 3" on center (about the diameter of a 20 ounce soda bottle) along the entire length of the wood.  Using 17 lb. masons line, we wove a grid around the screws weaving the string above and below the crossing grid.  A longboard worked well to roll underneath the frame to weave the string.

Step 6: Cap Preparation

Picture of Cap Preparation
Each cap needed to be drilled with a hole so the string could easily fit through, but not large enough for the washer tied to the end of the string would also come through.

We used a drill press with a 1/8" bit to drill the holes.

Step 7: Attaching Strings to Grid

With all 1,581 strings cut and labeled according to the coordinate system, the strings can be glued and tied to the grid.    We used a combination of first tying the string to the intersection of the corresponding strings according to the label on each individual string, and then applying hot glue to strengthen the knot.

Step 8: Attach bottles to frame

Picture of Attach bottles to frame
IMG_0059.JPG
http://youtu.be/HjEfan1F7KM

This step took 8 people several hours to complete.  We attached bottles with a specific color of liquid in each bottle to a string with a corresponding label.  Each bottle was filled with as little liquid as possible so as to minimize weight and to give the appearance of a flower pedal at the bottom of the bottle.

Step 9: Moving it!

Picture of Moving it!
Good luck with this one! We removed the bottoms of trash cans that had wheels on them and set the four columns on top.  We moved it to downtown Lincoln, Nebraska at 5:45 a.m.

Step 10: Public Display

Picture of Public Display
Peter Olshavsky 2.JPG
The structure was on display at a number of locations around Lincoln, Nebraska.



Additional Images:
http://www.behance.net/gallery/(POP)culture/3874285
 
Remove these adsRemove these ads by Signing Up
petraq8 months ago
Awesome
msaggese11 year ago
idea fantastica..
pvanwormer1 year ago
Really like this and may make something similar for my backyard.
dardy_71 year ago
I think this project was constructed very well. However I'd like you to elaborate as to how you came across your desired form in rhino
cle grand1 year ago
Awesome Job!
WUVIE1 year ago
Wow. What a great amount of work! Fabulous result!
OMG that is a labour of love for sure
samie8281 year ago
This is a very good environmental creation, I like it.
Thank you for sharing this idea.