Instructables

Paracord bracelet with a side release buckle

Featured

Step 1: Materials

You'll need paracord, or equivalent 1/8" diameter cord, a tape measure or ruler, scissors, side release buckle, and a lighter(torch lighter works best). The amount of cord used can vary, but for this example, we'll use 10 feet of paracord to start with. Actual amount of cord used for the bracelet is about 1 foot of cord for every 1 inch of knotted bracelet length. So if your wrist is 8 inches, you'd use approximately 8 feet of cord.

Step 2: Measure wrist

Wrap the paracord around you wrist and make a note of where the cord meets. Hold this point next to your ruler or tape measure and that's your wrist size.

Step 3: Find the center of the cord

Hold the ends of the cord together and find the center of the loop. Take the center of the cord and pull it thru one end of the buckle(either side of the buckle, it doesn't matter). Now pull the cord ends thru the loop until it's tightened up and attached to the buckle.

Step 4: Finding the bracelet length

Take buckle apart and and pull the free ends of the cord thru the other part of the buckle, sliding it up towards the attached part. You're going to measure the distance between the two buckle ends for the bracelet size for your wrist. Add about 1 inch to your measured wrist length, this will make the finished bracelet a comfortable fit. You're measuring from the end of the female part of the buckle to the flat part of the male end of the buckle(the part with the prongs, they don't count for the measurement because the fit inside the female part of the buckle when the bracelet is closed.).
sixtrees4 years ago

Great job,  you inspired me to make one of my own. I didn't have a snap buckle though, so I modified mine.

Picture 688.jpgPicture 689.jpgPicture 690.jpgPicture 691.jpg
darman12 sixtrees8 months ago
I love the loop, how did you do it?
 This looks great - do you have an instructable on how you did it? I can't work it out from the photos.
OK, I don't think I need to post a full instructable for my bracelet because I just combined two posted instructables. But I will tell you what I did.
Measure your paracord according to stormdraines version, but add 1 foot. Tie the knot that is in this version. http://www.instructables.com/id/In_and_out_Knot_and_loop_Bracelet/
So I started it like kcardwel's but instead of tieing it to furniture and using a seperate piece of cord, I braided it like stormdraine. The end part was a little tricky. I braided it to the end until there was only enough room to fit the two loose ends of cord through the loop. I had one slightly longer end so I used that one to form the loop for the  big knot, I think I tied a knot so the loop was in place. I then loosely wrapped the ends around the loop 3 times and then fed the cord through those loops (like a noose). I then pulled them tight and ran them down under the braids of the bracelet.  
Hope this helps :)

Wow that bracelet looks awesome u should make an instructable for that if you haven't already tell me when you do.
 
Zeke330i4 years ago
 Thanks for the great Instructable! I've been looking for a new collar for my Mastiff, Zeke, for a while now and thought the King Cobra stitch would look pretty good. I used 45' of Bright Red (wife's idea) 550 Paracord and a 3/4" side release buckle, both from Supply Captain (thanks for the link). I also re-appropriated a "D" ring from an old collar so I could hook a leash to him for walks. Using some extra 550, I made a few Chain Sinnet bracelets based on the instructions from your blog. Great stuff, thanks for posting. 
Survival Dog Collar1 002.jpgSurvival Dog Collar1 003.jpgSurvival Dog Collar1 008.jpgSurvival Dog Collar1 010.jpgSurvival Dog Collar 005.jpgIMG_1610.jpg
JKMax5 days ago

I just made this, and it was easy. I did a few modifications though. I wound about 25-30 feet of 12 lb test fishing line around the inner cords, and then put two small fishing hooks inside a small strip of aluminum foil, which can be used to lure the fish with it's reflecting capabilities. The fishing hook package has a small piece of electrical tape around it and I attached it towards the buckle area. It is a tiny bit larger than the rest of the bracelet, but since the buckle is underneath your arm, it doesn't show. Now if you have to use it for actual fishing...you have your hooks and line. You could also put a couple of split shots (weights) in there, but being mostly lead, I think I will put those inside the ends of my new paracord shoe laces! Just thought of something else...you could attach a bobber to the bracelet as a charm!! Just kidding.

When I think back to the first time I was on Instructables, I think it was when I found this via Google search. I thank you for that :)

I would like to say thank you for making a very good Instructable and it was just nice and easy to use. I have just one question, my bracelet keeps twisting like it is winding up and if you could tell me what I am doing wrong that would be nice? Thank you in advance.

LynnAnderson made it!2 months ago

Love it, Thank you :)

083.JPG079.JPG070.JPG018.JPG
gazumpglue2 months ago

Thank you for the time and effort you've put into these tutorials.

gazumpglue2 months ago

very nice work

Psychoclown972 months ago

I have just started doing paracord projects & your website is awesome. Things are clear & tell me just what I need to know. I am enjoying this very much!

IM000250.jpg
chimplost2 months ago

I love making these I am thinking about starting a business

but I need some tips

XaqFixx2 months ago

Just purchased a kit with TERRIBLE instructions, you 'ible was a life saver!

ok, I looked at your other instructable on how to do that one with the watchband, and i was wondering if that would work with the watchband to.
Stormdrane (author)  That Survival Freak3 months ago
Yes, you can remove one watchpin to gain access to the back of the watch for swapping out batteries on several different type paracord watchbands, or even switch watches if they are similar in size/construction to fit the spacing of your watchband knot work. ;)
steveazhocar3 months ago
Great tutorial! I especially like the other bracelet variations. Thanks for spreading your knowledge!
steveazhocar3 months ago
Great tutorial! I especially like the other bracelet variations. Thanks for spreading your knowledge!
LionVengance4 months ago
Thanks
Theclayton5 months ago
Great tutorial! I especially like the other bracelet variations. Thanks for spreading your knowledge! Paracord bracelet instructions
Rdenn991 year ago
Maybe I've missed it in your comments below, but could you show us how you made the 2 color braclets... The pic above shows it in black and brown.
Thanks
Stormdrane (author)  Rdenn991 year ago
Sew, melt, or glue your two paracord colors together, then tie following the instructable, with the connected section in the center of the bracelet and knotted over.  If you were using 10 feet of a single color, you'd use two 5 foot long sections for a two color version. ;)
so for a child size if their wrist is 5.5" i need about 6 feet of cord, total, even if only one color?
Stormdrane (author)  skizyx985 months ago
That would be around what you may use for that size bracelet, but depending on how you tie the bracelet(tight or loose, the buckle you use, diameter of cord), you may use less or more than that.

I usually overestimate what I need, because I can always use leftover excess cord for other things, zipper pulls and such, but having too short a strand of cord to finish a project doesn't leave you with many options to finish it.

Once you've tied several, you can narrow down exactly what you need based on your own tying style, and that helps eliminate waste. ;)
thank you! i ended up using around 6' i think. using a buckle closure. we'll see how it fits my nephew, i'll keep ya posted! have you shown instructions with the loop/knot closure method? i'd be interested in seeing that option also. makes it easier if you don't want to purchase buckles. thanks again! simple to follow!
Stormdrane (author)  skizyx985 months ago
I've not done an instructable with the knot/loop closure. Here's another knot tyer's tutorial for tying one with knot/loop or sewn on BDU button closer options. ;)
thank you, again!
Stormdrane (author)  Rdenn991 year ago
For a doubled Solomon bar/Portuguese sinnet/cobra stitch, you just tie the same knotting pattern over the first bracelet as a core. See my comment of this instructable from 'Mar 16, 2007' for a few photo links of the process.
jarrettgreen7 months ago
What size buckle did you use?
Stormdrane (author)  jarrettgreen7 months ago
The buckle used in the instructable was a 1/2" curved/contoured side release buckle, but you can use various sizes, colors, styles that are currently available nowadays... ;)
Thanks for the quick reply! Started looking around and realized there were a TON of choices.
cpowell177 months ago
I want to make a dog collar for our large breed dogs...90# yellow lab & rottweiler mix. Will the burnt end hold for large dogs or is there a different technique to use for them??

Thanks for the help :~)
It might be a good idea to melt the two ends together. Using tweezers, forceps, or pliers... Burn the ends, and while still hot and soft press together and flat...
Stormdrane (author)  cpowell177 months ago
You can pull/tuck the end strands back into a bracelet or collar, using a lacing needle or a pair of hemostats. Work the end strands alongside the core strands, under a few knots, then trim and tuck to finish. 

Tucking and hiding the end strands can be done with many different variations of knot projects, as an alternative to melting, gluing, or sewing to secure and finish.  ;)
cpowell177 months ago
Thanks, Stormdrane :~) I appreciate your help!!
bfarnell7 months ago
Bracelet and lanyard done. Great instructions! Cheers.
2013 16:45.jpg
clickworried7 months ago
Thank you for the time and effort you've put into these tutorials.
darman128 months ago
When I think back to the first time I was on Instructables, I think it was when I found this via Google search. I thank you for that :)
crabmanwill9 months ago
I would like to say thank you for making a very good Instructable and it was just nice and easy to use. I have just one question, my bracelet keeps twisting like it is winding up and if you could tell me what I am doing wrong that would be nice? Thank you in advance.
Pro

Get More Out of Instructables

Already have an Account?

close

PDF Downloads
As a Pro member, you will gain access to download any Instructable in the PDF format. You also have the ability to customize your PDF download.

Upgrade to Pro today!