Picture of Pressure Sensor Matrix
Four separate pressure sensors not only give feedback about where I'm pressing, but also how hard. The sensitivity is ideal for finger pressure. Though it is not linear, it is stable. Very sensitive to light touch and then it takes a lot of pressure to reach the minimum resistance.

The inside looks just like the fabric pressure sensors, except each stitch is connected to a separate conductive fabric tab. The downside is that separate tabs and connections to these tabs take up a lot of space, especially if you want to achieve a tight matrix of sensors. A grid of lines and columns and some code to analyze these (separately power and measure) would allow for much tighter spacing. This version is nice because it is so simple.

To make the sensor fully fabric one can use EeonTex conductive textile (www.eeonyx.com) instead of the plastic Velostat. Eeonyx normally only manufacture and sells its coated fabrics in minimum amounts of 100yds, but 7x10 inch (17.8x25.4 cm) samples are available free of charge and larger samples of 1 to 5 yards for a minimum fee per yard.



This Instructable covers two slightly different versions of the pressure sensor matrix. The only difference being the spacing of the individual pressure sensors in the matrix. In one of them they are placed practically next to each other (white) and in the other there is a 1cm space in between each sensor (purple), but because of the thickness of the neoprene it is not possible to press in between the sensors without pressuring a sensor. Hope this makes sense.

I am also selling these handmade Thread Pressure Sensors via Etsy. Although it is much cheaper to make your own, purchasing one will help me support my prototyping and development costs >>

The materials used for the sensor are basically cheap and off-the-shelf. There are other places that sell conductive fabrics and Velostat, but LessEMF is a convenient option for both, especially for shipping within North America.

Velostat is the brand name for the plastic bags in which sensitive electronic components are packaged in. Also called anti-static, ex-static, carbon based plastic bags... you can also cut up one of these black plastic bags if you have one at hand. But caution! Not all of them work!

To make the sensor fully fabric one can use EeonTex conductive textile (www.eeonyx.com) instead of the plastic Velostat, but at the moment EeonTex conductive textile is only available in a minimum of 100yds. But try ordering samples!

I chose to work with neoprene because it offers a form of natural force-feedback and also it is great for sewing into with the conductive thread and thus isolating it. But you can easily replace the neoprene for some regular stretch or non-stretch fabric and even try felt or kind of rubber.
1-40 of 41Next »
mangomelonegg5 months ago

Would it be possible for the links to be updated?

Plusea (author)  mangomelonegg5 months ago

so sorry everyone who has been waiting for the links! finally, here:

>> http://www.kobakant.at/DIY/?p=3314

JoshuaS26 Plusea2 months ago

I am really interested trying this but when I tried using the links at this address: http://www.kobakant.at/DIY/?p=3314 I got a "404 page not found error". Is there anywhere else I can find this code?

Thank You

Instead of using the software can lights be added to check if it works?

All the links for the code in the Arduino software are dead. Do you have the codes somewhere else?

windrago4 years ago
the links are dead - do you have the code somewhere else?
Plusea (author)  windrago4 years ago
check these links here: http://web.media.mit.edu/~plusea/downloads/code/

sorry for the inconvenience!
mcti Plusea1 year ago

Have you updated this link? I am told I don't have permission to view this page. Thanks!

omtinole Plusea3 years ago
Which of these is the 2x2 matrix visualization code? The file names are rather cryptic.
Plusea (author)  omtinole3 years ago
good point. i have tried to start organizing my code better. please see this link: http://www.kobakant.at/DIY/?cat=347
and check back by the end of next week.
swoudlxy1 year ago

Hi Plusea,

May I ask what is the power consumption for each pressure sensor? Many thanks for your help.

BadPuns1 year ago
I was wondering if you could be bothered to write or direct me to an in-depth tutorial on connecting this to an Arduino or Raspberry Pi?
Plusea (author)  BadPuns1 year ago
here is a good tutorial >> https://www.sparkfun.com/tutorials/389
BadPuns Plusea1 year ago
Thanks a lot. I don't have an Arduino yet because, strangely enough, my parents don't trust me plugging things in and downloading stuff on their computer. I don't know why they wouldn't trust me, of all people...
khetarpal1 year ago
Hi Hannah,

Thanks for sharing this. I have learnt a lot from your instructables. I'm working on a creating a pressure map for a healthcare application. Would be great if you could elaborate on Velostat vs Eeonyx fabric pressure sensitive properties. I understand that sewing convenience / stretching capability are obvious benefits of using Eeonyx, but what about the pressure sensing range & electrical properties. Does Eeonyx provide a more linear resistance signal when changing pressure? Does it have less hysterisis compared to Velostat?
daleruisky1 year ago
Thanks so much for putting this together! Your links to the companies selling the materials is invaluable; saved me hours of research. Keep up the great work!
vijayrex2 years ago
Hi, i have a doubt. How do i get the visualizing in the processing? I have both of ur arduino and processing codes. Uploaded the arduino code to the UNO board using Arduino software and when i try to run the processing code in "processing" software it just opens a small blank window.. Can you please help me?
agomes63 years ago
amazing work! you're an inspiration for all of us!

I have one question one the fusible material....is there a specific one you'd recommend or this should do it?:


Thank you for your wonderful input in this community!
Plusea (author)  agomes63 years ago
thanks for your comment! while i have not used this particular pellon product, from the description it looks like it will work for fusing (heat gluing) two pieces of fabric together.
agomes6 Plusea3 years ago
not particularly this instructables but...success :)


your kits are fun! following up on your work for a workshop proposal quite soon (ACE). you're the best ! thanks
Plusea (author)  agomes63 years ago
thank you so much for this comment and for sending the picture. it is so nice to see what becomes of the kits once they are shipped to people! i hope things worked well for you. i'm always grateful for any feedback on how to improve them.
agomes6 Plusea3 years ago
no problem!

this one (several of them actually) were sitting around at my lab and I recognize them as being yours :)

I think this one is neat as is, no improvemente needed :)

Note to unexperienced users with sewing related materials....neoprene cannot be ironed (or not directly anyways...I know that now :) ) good luck with all your future work, I'll look forward to keep following it
scanlinj073 years ago
Great work...I was curious if there was a way to build this so that the information from the analog function (stepping on or pressing the mat) can be stored and then extracted later, like after a day, to view on the computer? So basically it would store the activity of how many times is was pressed and for how long and then that data would be stored and viewed after a period of time?
shall64 years ago
Is it possible to adapt this to handle high impact? I'm looking into making a body suit for sports-impact analysis.
windrago4 years ago
thanks super Plusea, you rock my fabric-world!
egasimus4 years ago
Hi there. First of all, I can't help saying that I like your work and I'm always glad to see a beautiful and ingenious girl in the field of DIY electronics. Keep up the good work! Compliments aside, can I still order samples from Eeonyx, and would they ship to Eastern Europe? I saw no mention of that on their site, and I'd really like to have EeonTex on my hands. The possibilities with that stuff are endless.
atomanttan4 years ago
Hi Plusea, your work is very interesting.
If I have a bigger pad and higher resolution, do you think I could use it as a pressure sensing seating mat? Do you have any pressure sensor matrix in stock at the moment as I could not find it at etsy. Thanks :)
Plusea (author)  atomanttan4 years ago
try it and see if it works. in general the velostat pressure sensors scale nicely.
here is a link to the kit on etsy:
>> http://www.etsy.com/listing/51675531/fabric-pressure-sensormatrix-kit
max05065 years ago
can you also make like a realy big one whith realy small touch squares to use it as a mouse/ touch pad for your pc.
Plusea (author)  max05065 years ago
yes you can and you can use a teensy board instead of the arduino (but still use arduino to program it!) so that you can fake mouse input directly! >> http://www.pjrc.com/store/teensy.html
aringe5 years ago
Currently using this design as a basis for my senior design project. I'll upload it once we finish.
pstretz6 years ago
This gives me a great idea for a midi controller pillow that would generate ambient music to help you sleep. It could change as you move your head.
john otto6 years ago
Your instructables are top notch and always innovative.Thanks... I'll be watching to see what else you whip up.
ste54426 years ago
Hi Plusea, nice work!
I can see all kinds of applications for this such as shoe insoles which can react to foot pressure and adjust accordingly, office chairs which can change shape based on how much pressure you place on each butt cheek etc etc!
I might just make one of these!


NachoMahma6 years ago
. Another great one from Plusea. How long can you keep this up?
techie6 years ago
This is another excellent idea. I made a glove for a theatre project with push buttons attached to the palm to turn on lights built into the costume. This sensor setup could be a really fantastic way to do the same thing but more subtly with the lights responding to the amount of pressure. Totally cool!
PS1186 years ago
Another amazing project! Sweeeeet! BTW, when are you going to make a fabric came controller? That woud totally rock! (Yeah. I say that as if your other projects haven't 'totally rocked'. ) I'm yearning for the PlayStation blankey, myself. :)
Plusea (author)  PS1186 years ago
you mean game controller?
one of my first Instructables was for "Massage me", which is essentially a wearable game interface for back massage >>
website >> http://www.massage-me.at/
let me know what you think.

thanks for the comment!
RPisces6 years ago
This is very nice, and creative. You should seriously consider emailing the Arduino.cc admin and asking them to place this in their tutorials section; they'd love it.
Sparrow156 years ago
What if somebody wrote a program that used this sensor? Basically, where you press could correspond to a pitch, and how hard could correspond to how loud. I think this would be an awesome instrument.
1-40 of 41Next »