Introduction: RC Car Controlled by Old Glove

In this instructable we build a remote control car using Arduino and the nRF24L01+ transceiver for wireless communication / control of the car. To control this car we won't be using the classic joystick, but instead an old glove! The glove will use an accelerometer (MPU-6050) to control the car's direction and speed based on the position of your hand. To access the Arduino code go to my blog: http://forcetronic.blogspot.com/

Comments

author
HameedA3 (author)2017-02-16

Hi sr

how are you?

i did watch the video and it's fantastic project, and I did understand

this project i working on it now for my project of the graduation and we will start the practical part , ""control on car by usng the glove""

what i want to know the equipments other than arduino and all conductors of the connection and the ways of connect all connections in car and on glove and connections between car and the glove , and does the connections on the car or on glove is hard?

and what s the cost or prices of all conductors on this project?

i want to know short note about this project or idea short note.

Thanks sir.

author
ForceTronics (author)HameedA32017-02-16

Note that this video is a couple years old so parts used and libraries used may have changed or have been updated since the making of the video

author
ForceTronics (author)HameedA32017-02-16

I believe the parts list and how it is connected was covered in the video, does the video not show up in the instructable? I don't remember the cost of the parts. Here is a link to the video on YouTube: https://www.youtube.com/watch?v=IjUlqe-aeGU

author
remaa (author)2016-08-13

hi sir, i have to control the robot car project. Where the rear wheels in the form of a dc motor is controlled with flex sensors and front wheels in the form of a servo motor controlled by the accelerometer sensor. Robot controller with a car connected with nrf24l01. if one of the sensors to control I can. but if it combines both to control I can not. Both sensors transmit data simultaneously . dc motors and servo motors confused receive data so that its movement is chaotic. How should I fix this? can you help me.? Can I send my program to you and you see.? Please. My email: rema_adhe@yahoo.com

author
remaa (author)2016-08-13

hi sir, i have to control the robot car project. Where the rear wheels in the form of a dc motor is controlled with flex sensors and front wheels in the form of a servo motor controlled by the accelerometer sensor. Robot controller with a car connected with nrf24l01. if one of the sensors to control I can. but if it combines both to control I can not. Both sensors transmit data simultaneously . dc motors and servo motors confused receive data so that its movement is chaotic. How should I fix this? can you help me.? Can I send my program to you and you see.? Please. My email: rema_adhe@yahoo.com

author
thebookworm11 (author)2016-06-21

Can you get the car parts by taking apart a regular RC car/truck?

author

You probably could but it is hard to say because there are so many different RC cars out there. If you did you would most likely have to make changes to either the motor drive hardware and / or motor drive code presented in this instructable

author

OK thanks. I'll take it apart and see what I get.

author
DũngN17 (author)2016-02-20

share code for me pls

author
DũngN17 made it! (author)ForceTronics2016-03-04

help me :)

2.png
author
ForceTronics (author)DũngN172016-03-04

Did you add the Adafruit motor shield library to the Arduino library folder?

author
DũngN17 (author)ForceTronics2016-03-05

i try library but it has been error, can you share library folder??? pls

author
Hambone22 (author)2015-10-30

This is kewl

author
robobot3112 (author)2015-04-15

great one. I will sure try this one out. Keep it high up.