Instructables
Picture of RC Car to Robot
main2.jpg
main3.jpg
main4.jpg
main5.jpg


Converting an RC car into a robot is a quick and easy way to get started with robotics. At the very least, when you get bored of playing with your remote control car after three days, you can turn it into a robot that will do all of your evil bidding. Well, maybe not all of it, but at least a sizable amount.

In this Instructable I will go over the bare minimum you need to get started. Think of it as a template for making a basic robot that can be expanded with sensors, code, and additional hardware to do some really amazing things. You can now impress your family, make new friends, and scare your pets with the power of robot magic.
 
Remove these adsRemove these ads by Signing Up

Step 1: Go Get Stuff

Picture of Go Get Stuff
You will need:

(x1) R/C Monster Truck (Radioshack #60-646)
(x1) Arduino Uno REV 3 (Radioshack #276-128)
(x1) Arduino Motor Shield (Radioshack #276-131)
(x1) Parallax Ping Sensor (Radioshack #276-136)
(x1) Heavy-Duty 9V Snap Connectors (Radioshack #270-324)
(x1) Size M Coaxial DC Power Plug (Radioshack #274-1569)
(x1) Multipurpose PC Board with 417 Holes (Radioshack #276-150)
(x1) 90-Ft. UL-Recognized Hookup Wire (Radioshack #278-1221)
(x1) Enercell® Alkaline 9 Volt Battery (Radioshack #25-853)
(x1) 6" Heat-Shrink Tubing (Radioshack #278-1627)
(x1) 5-1/2" Zip Ties (Radioshack #278-1631)

Step 2: Remove the Cover

Picture of Remove the Cover
2B.jpg
2C.jpg
2D.jpg
Flip the RC car over and remove the two screws holding the cover in place.

Put these screws aside somewhere safe for later reassembly.

Step 3: Unplug

Picture of Unplug
3B.jpg
Unplug the motors from the connectors on the main board.

If your remote control car is hard wired to the motherboard, cut the motor wires loose.

Step 4: Remove the Controller

Picture of Remove the Controller
4B.jpg
4C.jpg
4D.jpg
4E.jpg
Remove the screws holding the controller board to the RC car and pull it free.

Step 5: Power

Picture of Power
5B.jpg
5C.jpg
5D.jpg
5E.jpg
Remove the cover from the M-type power plug and slide it onto the wires for the 9V connector (such that you can twist it back on after you solder the wires).

Solder the red wire to the middle connection tab. Solder the black wire to the outer connection tab.

Twist the cover back onto the plug.
1-40 of 72Next »
abencomo6 months ago

Nice tutorial, thanks for sharing! We built a similar project. However, we installed an Android device onto a RC car and used an IOIO board instead to control it autonomously. Here is the preliminary result:

hi abencomo, really u have done great job, can u send the details of ur project, like app which follows the ball, code and schematics to my mail arun3491@gmail.com.

AlB1 arun349128 days ago
All the information and code is here:

http://www.socsci.uci.edu/~jkrichma/ABR/index.html#SOURCE%20FILES
GochtG arun349128 days ago

That's great! Can you tell me more about your project? (agocht@gmail.com)

Great Instructable! Your build and pictures are so clean! Thank you so much for documenting this so clearly!

The choice of adding a motor shield kind of confuses me, though. If you have a steady hand then connecting four wires to the car's RX chip and taking advantage of the car's already present H-bridge is pretty simple. You can even send PWM signals and it works to control the motor's speed.

If you already have a motor shield or don't want to solder to a surface mount chip then I totally understand, but one can easily cut out $20 to $30 of the cost of this project with some careful soldering.

Can you pls share the wiring on the car's RX chip and/or the H-Bridge?

S0uraV_DAS3 months ago

Awesome work! I am building it now!

iliriano6 months ago

Thanks for the great instructions and pictures. My son and I just finished the truck and it worked. However the truck is only going foward and to the right, it pauses and repeats again. When I copied and pasted your scripts a bunch of extra spaces were added between the lines. I will delete them to see if this is the fix?! Otherwise we will have to recheck the Ping soldering and wiring to the Arduino motor shield, to find other errors.

Can you screenshot the code? I haven't done anything arduino but I do know a bit of code.

vkadnor9 months ago
can i use arduino leonardo and l298 ic motor shield
tarroyo210 months ago
How possible to pull this off using a Sensored Brushless Motor system? Novak is what I am wanting to use).
NASCAR1810 months ago
Do you know if these sensors will work? "Ultrasonic Module HC-SR04 Distance Measuring Transducer" If not does anyone have code for these? great project!
tharindurc 11 months ago
can we use a different arduino motor shield
randofo (author)  tharindurc 10 months ago
Yes, but perhaps not with these instructions. These instructions are centered around this shield.
12y11 year ago
is it possible to solder jumpers directly to the IC?
vek111 year ago
Instead of using a motorr shield, can I use a motor driver ic(SN754ONE)
Thanks for the great instructable! Could I use this motor shield? http://www.radioshack.com/product/index.jsp?productId=13351656 I am new to all of this stuff. Thanks
I have made a similar kind off project but instead of an arduino motor shield and a ping, i have attached a adafruit type of motor shied and a hc sr 04 sensor . can you please help and modify this coding for an adafruit motor shield along with a hc sr 04 sensor .
randofo (author)  mihir.crazi1 year ago
No, but please share your code if you do.
mike0101011 year ago
You mentioned that the front motor was the "turn motor". how exactly does that work? does it actually turn or spins the left or right wheels to achieve turning? I'm wondering if one would need 2 motor controllers for an RC that has for motors
randofo (author)  mike0101011 year ago
If it has four motors, then you might. Mine has two motors. One drives the back wheels and the front one turns the axle left and right.
angpal591 year ago
works great but my wheels wont turn, they stay where they are when I fire it up but other than that it works perfect.
angpal591 year ago
(removed by author or community request)
randofo (author)  angpal591 year ago
I don't know anything about that shield. I don't know who made it, the pin mapping, or the specs on it.

Unless it is explicitly stated somewhere, never assume any electronics component is interchangeable with any other. I recommend searching the internet for instructions to use exactly what you have.
but to tell you the truth randofo, it's been so long it could of came from overseas, I'm trying to find out now, I will get back with you sometime
angpal591 year ago
I am trying to delete one of them but having a hard time, bear with me please
angpal591 year ago
Here it is, older motor shield, can I use this one?
DSCI0062.JPGDSCI0062.JPG
leeseibert1 year ago
Thanks for the How to.

I am working on a project very much like this. See my video here: https://www.youtube.com/watch?v=SPLlTAVeIf8
Good day! I have one question about this project. Should I use Xbee modules to connect PC with robot??? I will be appreciate for your answers!
shar21 year ago
may I know what's the purpose of connecting the ground socket on the shield to the input ground screw socket on the motor shield?
dude should you only use new bright cars

hilmara1 year ago
Hey there, I used same arduino, same motor shield, same ping sensor, same code, but different rc car, basically the same two simple motors, but somehow my car moves only forward, with a short little stop, than moves again forward even if there are objects, like my hand or foot, It never reverse and doesnt turn the wheels. Can anyone help me? something wrong with the code or ?
shar21 year ago
Hi, I've used exactly the same kind of Arduino, motor shield, Ping sensor and code but different RC car for my project. However, the rear wheels turn forward and then reverse repeatedly when there is no obstacle. It works fine when there is an obstacle. May I know what's the problem?
hey, I had the same problem. Different car, anytime I power it up. it moves forward then backwards repeatedly, but when I keep my hands in front of it, keeps moving forward
hilmara1 year ago
Hi there, cool project. Im planning on doing my own. I got this old r/c car wich only has one motor, the rear one is that okay ? do I have to fix the code? and second, what do I do with the originally on/off button and its wires? thanks in advance !
hello when i put in the cod e every thing works fine but every 5 second the motors stop and some times the ping sensor does no always work is ths normal
shar22 years ago
Where did you connect the wires from the battery pack and from the switch to?
randofo (author)  shar22 years ago
I am no longer using the car's battery pack and switch. It is all powered off the 9V.
009agent2 years ago
How would you go about removing the Arduino so you can use it for other projects. I understand you would need an ATMega chip.
randofo (author)  009agent2 years ago
1-40 of 72Next »