XBOX 360 Controller Rapid Fire Mod

This will show you how to modify your XBOX 360 wireless controller to get rapid fire with the right trigger using a mod chip

**you will need experience with soldering as some of the points are very small

**it is possible to destroy your controller in the process (dont blame me, i didnt do it)

Step 1 What controller do you have?

the easiest way to tell which board you have is to take the battery pack off the controller and look at the board before you open it

another way to tell which board you have is by the way the board looks (see pictures)

Comments

[alien200049655]

will the mod work with (wired) controllers?
I've got the wired USB version.

[harrycarry250]

well i didint work for me but i may have done it wrong. my 555 chip didnt have a notch, just a dot so i dont know if they coardinate or what. my controoler just shuts off when ever i engage the switch.
Thanks. Good DIY

[Modscientist]

Usually on a chip the dot will be positioned toward the front left most pin to indicate pin one Looking at it from the top with pins facing down. Check schmatic. Check diagham or another source for power and inputs outputs and grounds.

[Legoman200119]

Chuck Norris ROCKS

[jrash]

Allot bigger please

[Buzzsushi]

Why would you spend the money to buy a kit when it takes the same amount of soldering and material to just use a pushbutton

[ol987986]

its like 10 times easier to go to a shop and buy a modded controller for like 12 quid

[RDSawicki]

u have to press the synk button to turn it on

[Andr3s06]

Which way are the pins facing? Because according to the schematic of the timer the number 4 pin is on the bottom left and the number 5 pin on the bottom right. I just want to make sure I'm doing it right.

[KAMAKAZIxKILLER]

is that a 555 IC ?

[stinger0410]

i think it is because the 555 IC is mainly the only used timing chip for modding as such

[runningduo]

Yes that is a 555 IC. If he knew how to hook it up right and did a little research on how to do it, then he would have a God given power mod. It would be insanely fast.

[ilike2killu2]

how does pin 7 have 2 solder points? becuase you said the 1k resistor goes to 7 for cg and now you have this to 7

[fredgt350]

Can you help, I have a CG model, can I make it rapid fire the easy way or do I have to use a timer chip, please any help will help, Oh sorry can youhelp

[stinger0410]

did you get a reply cause i want to know how to use a timer chip to do the mod

[madphysicstutor]

dude i did what u siad the 4th player led lights up when it is on but nothing happens it doent shoot or anything can u help i use a TLC 555 timer ic

[venchilla96]

wana make your pictures a little bit bigger please. its hard to see

[Barlie_pop]

how do i turn on the mod

[VI Coheed IV]

haha nice 'able. nice use of MSPAINT too.

[KAMAKAZIxKILLER]

where exactly is the black wire located at?

[swany34]

The black wire (neg) goes from the far right of the 4 solder points in the middle of the controller, to the number 8 point on the microchip

[Michael Roberts]

 other way around cG has tp19....

[Michael Roberts]

 hmmm, maybe i am mixed up. one bad source and thats what i got. ill let you know if i find out anything

[swany34]

I have checked my sources and the pictures shown are correct, cg might have tp 19 in a different place?

[S1L3N7 SWAT]

Why would you want to have rapid fire for the left trigger? Usually people put it on the right so they can use it in FPS. Unless of course you're left handed.

[Br14n]

I have this on both of my triggers, it's good for dual wielding weapons.

[swany34]

my bad- ment to put right trigger, thank you for finding that

[Crate Digga]

Has anyone tried this yet and if you have does it work???