Instructables

KNEX HAND GUN (Accurate and Strong)

Picture of KNEX HAND GUN (Accurate and Strong)
This is what we are going to create:
 
Remove these adsRemove these ads by Signing Up

Step 1: Parts

Picture of Parts
This is what we need:

- 34 yellow connectors
- 4 green connectors
- 3 orange connectors
- 1 white connector
- 3 gray connectors
- 2 red connectors

- 2 yellow rods
- 5 grey rods
- 4 white rods
- 6 green rods

- 2 blue washers
- 2 grey washers (thicker then blue ones)
- 1 black (kind of) connector
- another 1 black (kind of) connector (another one)
(close-ups in following steps..)

- 7 small rubber bands (THIN ONES)
- 1 scissor

Step 2: The Barrel

The Barrel is realy simple..
Just follow the images, and you will be fine..
I added some information with those yellow boxes.

Step 3: The Handle

Picture of The Handle
PICT1024.JPG
PICT1026.JPG
PICT1027.JPG
The same.. Just follow the images and notes ;)

Step 4: The Trigger

Just follow the images and notes..
You have to force some parts into their place..
View the notes to know which parts!

Step 5: The Pusher ;-)

Picture of The Pusher ;-)
PICT1049.JPG
PICT1050.JPG
You just can't do this wrong.. Just a stick with some connectors and a rod... Watch the pictures..

Step 6: The Rubber Band

Picture of The Rubber Band
On the pictures you can see where to place the rubber bands..
It can be hard, but ask your questions, if you want to! ;)

PS: The first rubber band is actually three rubber bands in each other.. You know how to do this right?

Grab one rubber band. Grab another.. Lay the half rubber band over the other one. Grab the rubber band that's on the bottom, and pull it into the other one.. Do the same with the third.. Only grab the second one instead of the first one..

(This sounds very wicked, but it isn't!)

O YEAH!!! MAKE TWO OF THEM!!!

Step 7: Extra Things

Picture of Extra Things
PICT1053.JPG
PICT1055.JPG
PICT1057.JPG
PICT1058.JPG
PICT1059.JPG
Just follow the images.. no comments.. too simple ;)
Between the third and fourth image is a note..
For if you don't get it!

Step 8: Preparing Rubber Band

Picture of Preparing Rubber Band
PICT1061.JPG
PICT1063.JPG
PICT1064.JPG
The last steps before you can load it up ;)
Yeeeeey, almost done :)

Step 9: Loading, Aiming, and Firing

Picture of Loading, Aiming, and Firing
PICT1067.JPG
PICT1069.JPG
PICT1074.JPG
PICT1070.JPG
Loading is simple, aiming is something tricky, firing is the simplest!

Just watch the pictures as always ;)
chato562 years ago
will it work without the black piece cause i dont have that one
smanzie44 years ago
just rods.
sebby38s5 years ago
What do you use as bullets?
xZCodmaNZx5 years ago
wicked gun i moded it and it is awosme
The Jamalam5 years ago
bad handle, but other than that, fine!
ultimate-tester (author) 5 years ago
Simple, but GOOD...
alfpwns5 years ago
simple yet good yet not a block trigger!
well, it doesn't look to bad, but it's very simple.
Pro

Get More Out of Instructables

Already have an Account?

close

PDF Downloads
As a Pro member, you will gain access to download any Instructable in the PDF format. You also have the ability to customize your PDF download.

Upgrade to Pro today!