Picture of Seat for a walker

I have a friend who has a disability. She tires easily and when she does she has a difficult time finding a place to sit when she needs it. I came up with this design that would be lightweight, removable, secure, could be hand washed, and would not be in the way when attached. The seat portion was recycled car seat harness from a child safety seat.
Remove these adsRemove these ads by Signing Up

Step 1: Gather tools and materials

Picture of Gather tools and materials

In this instructable I used

sewing machine
seam ripper (not pictured)

length of car seat harness webbing
1" flat nylon webbing
Heavy duty upholstry thread
4 1" welded steel D rings
8 1" welded steel O rings
4  3/4" electrical conduit claps (dipped in plastic dip prior to use)

To attach to walker I used
flat headed screwdriver

Step 2: Decisions of size

Decide how large you want the seat portion. I chose to make this seat for an adult so I wanted it fairly large. 

Step 3: Cutting side lengths

Picture of Cutting side lengths
Cut 2 lengths of the wider webbing into 13.5" pieces. Flash in a lighter flame to melt ends to prevent fraying. Fold over ends and make the loops a tiny bit wider then the webbing itself. You will need to pass the O rings through the loops. Stitch back and forth 4-5 times. Repeat on each end. You should end up with 2 straps with loops on each end.

Step 4: More cutting

Picture of More cutting

Cut another 2 lengths of the wider webbing. Melt ends to prevent fraying.  I chose 16" lengths. Insert the lengths into the looped ends and sew together using a straight stitch with machine. Sew only on outside edge and go forward and reverse 4-5 times.

Step 5: Cutting supports

Picture of Cutting supports
Cut 3 lengths of wider webbing into desired sizes. I chose 15.75".  Melt ends to prevent fraying. Attach each piece to the underside of the frame, spacing each evenly. Use a straight stitch and go forward and reverse 4-5 times. Repeat on the other side.

Step 6: Cutting more supports

Picture of Cutting more supports
Cut 7 lengths from the wider webbing in 8.5" lengths. Melt ends to prevent fraying. Attach onto frame underside on the longer side using straight stitch an going forward and reverse 4-5 times.
reddnekk4 years ago
Great idea. And--if you don't have a sewing machine, all straps can be riveted--riveter is cheap in handicraft store (Michael's, for example). And hammer can be used if no riveter available (altho you DO have to have rivets). Use at least four rivets per joint, space so they are not in line. And seat can be one piece of canvas with straps riveted along two opposite edges. (I don't have sewing machine, but DO have riveter.)

Now why didn't I think of this?
I like to use rivets and contact cement (two layers)
two layers contact cement
clamp then rivet
jblessf4 years ago
This is wonderful! It is light weight. Which makes it easier to use the walker. The ones that are sold in stores are too heavy. My hat is off to you.
nneul (author)  jblessf4 years ago
That was one of my "requirements" when I brainstormed this up. I looked around but all of the available seats (If you could find one) were very heavy or bulky and not convenient to carry around at all times. This is very portable, hand washable, light weight, sturdy, and adjustable.
laurel14 years ago
I worry that the clamps would slip off of the handle and dump the person to the floor.
If the clamps were put on the side support bars, and could slide back and forth, the seat could be pushed back when the walker is folded. The blue straps, on the corners, could have INDUSTRIAL velcro to attach around the legs to keep the seat square when sat upon. I think that the clamps still should be used to provide extra strength.
Also, I don't know where to buy these, but there are wheels for the back legs that collapse so that the walker doesn't roll when someone sits on it. They sort of lift so that the weight is on the leg and not on the little wheel. These are usually on the walkers that have the flip seats. They have larger front wheels and these smaller collapsing wheels are on the back legs.
OK, grannie with a walker gave her two cents. I'll be interested to see how someone will improve on this. Oh, and don't forget to mention a weight limit so that a heavier person doesn't get hurt.
If anyone sees these collapsing wheels for sale anywhere, please let me know.
nneul (author)  laurel14 years ago
The clamps are something that was a concern. I tested it with my own weight before I allowed anyone to use it. I weigh right around 240. It didn't bulge or wiggle at all. I then sat in it for around 30 minutes just to test the strength. It was not the most comfortable seat but then again I am larger then the intended person it was designed for. This would be great for someone who needed short but frequent breaks.

If you have never messed with plastic dip it sure is a lot of fun... Gooey, messy, stinky, but fun. :)
Jadagara4 years ago
A great idea indeed. My wife has tumor on her spine and she now needs a walker to move around when she prefers that instead of on a wheelchair. Like your friend, she tires easily so a seat like this would be a relief during those moments. Thank you for sharing.
jneul4 years ago
Great idea. Simple, functional, relatively inexpensive