Step 6: Attach the casters

Attach the casters to the bottom of the table posts by simply threading them in place. Adjust the height of the table so that it is right for you.

A standard counter is around 34" - 36".

<p>Great stuff. Detailed explanation and pictures. The legs are great I have used them before and they turned out to be ok.<br><br>http://beltsanderworld.com/</p>
Great idea. Just what I'm looking for. The Grainger legs, however, do not seem to come with the posts. I contacted Grainger and they couldn't tell me whether they came with posts or what locking casters would work with the legs. Any help would be appreciated.
I am 90% certain they came with threaded posts, but I don't remember fully.
You need to support the legs like the one with the shelf. &nbsp;If you are rolling that baby around and hits something your legs will fold under using wood screws. &nbsp;You should consider using&nbsp;carriage bolts and counter sinking them, then fill the holes with harding putty for a smooth&nbsp;surface. &nbsp;Then you could cover the tops with&nbsp;counter top laminates, wood is very soft. &nbsp;They make a great work area, are cheap and very durable and if you do gouge the surface you can just replace it.<br /> <br /> If you wanted to lock them together get some Table locks. &nbsp;This is the best place to order hardware, &nbsp;I think.&nbsp;<br /> <br /> <br /> www.rockler.com<br />
<a href="http://www.rockler.com" rel="nofollow">Rockler </a>is a great supplier; I enjoy just browsing their catalog. They have so many things you never knew you needed!&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; :-)<br /> <br /> You believe you can get table locks at your local big box store and save the shipping costs.&nbsp; I've also used <a href="http://www.lowes.com/pd_311971-1277-V1848_0_?newSearch=true&amp;catalogId=10051&amp;productId=3151985&amp;Ntt=311971&amp;N=0&amp;langId=-1&amp;storeId=10151&amp;Ntk=i_products&amp;ddkey=http:SearchCatalogDisplay" rel="nofollow">brass latches</a> from a big box for&nbsp; $3.50 for a pair.&nbsp; These are a good alternative for a workbench.<br /> <br /> They are easy to install, but you have to be absolutely sure everything is lined-up properly.&nbsp; Assuming the goal is to lock two of these workbenches together, here is how I would do it:<br /> <br /> 1 - Turn the table over, face-down on a clean piece of the floor<br /> 2 - Ensure the mating edges are properly aligned in all three axis<br /> 3 - With both halves of the locks locked to each other,&nbsp; position the locks where you want them and use a pencil to locate the mounting holes for both halves<br /> 4 - Drill the pilot holes for one half only<br /> 5 - This next step is my trick: Drill the pilot holes for the 2nd half about 1/16&quot;&nbsp; (1.5mm) further away from the edge than the pencil marks indicate.&nbsp; The purpose is to ensure a tight fit when the two halves are mated.<br /> 6 - Screw-down the table locks<br /> 7 - Align and lock the two tables.&nbsp; You should have some resistance because of step 5.<br /> 8 - Flip the table upright<br /> 9 - Adjust the casters as necessary to ensure the height of the top surface is uniform in all four corners<br /> 9 - Celebrate a job well down with a hoppy <a href="http://oregonbeer.org/" rel="nofollow">Oregon microbrew</a>!<br /> <br />
I ended up adding shelves to both tables, but that is a good point. If I hadn't done that, I would definitely have that problem. <br /> <br /> And I considered lining the top with mat white acrylic like my desk at home, but decided I was going to stick with the plain plywood because it is nice to photograph on (not to mention, I was working on a relatively tight budget). It will probably get scuffed up over time though, but I'm hoping that will add character.<br />
&nbsp;They look great. &nbsp;Your pictures are very good and you took some with your left hand or had help either way nice job. &nbsp;
I've added your feedback to step 5 (if you don't mind).<br />
-Legs giving way. Even if you do not add shelves, adding a single rail will keep the legs from giving way. If you have 2 rails, (hence something going all the way around) they can get in the way of your ankles sometimes, so one down the middle, back out of the way, is all that is needed. For single rail it needs to be very staunch, because it needs to also be able to take a load, as well as handle any forces applied while rolling the bench about.<br /> <br /> Inspirational project, thank you for sharing.<br />
&nbsp;or you could set two long rails from one corner to the diagonal corner
Very cool.&nbsp; As an aside, I've seen similar legs for sale in Ikea.<br />
&nbsp;dont bother with those as they have a very limited weight range...... i figured this out after overloading some with 2 mac pros...thankfully the monitors were wall mounted
Nice depth of field! What did you use to take the picture of the leg with the background?<br />
&nbsp;Looks to me like a mixture of the leg not being entirely in focus and a small aperture.
&nbsp;1<a href="http://www.instructables.com/id/Treadmill-Desk/" rel="nofollow">. Memo from the boss said &quot;rolling floor, stationary workbench&quot;.<br /> </a>2. You can put company property up for sale?<br /> 3. Noahw's seat is still warm and you comandeered his space...how could you?<br /> 4. Nice. Do you need International Space Station docking connectors to keep the two workbenches together?<br /> <br />
1. I have a doctor's note about motion sickness.<br /> 2. So long as the $10 is reinvested back into cookies for everybody. <br /> 3. Talk to Scoochmaroo about that one...<br /> 4. No, the floor is sloped at just the right angle(s) to keep them together.
...and those people who do not have the planet on their side could counter-sink neodymium magnets into one edge of each desk.<br /> <br /> When you're not sticking furniture together, they could be used to hold up tools or as a convenient way to wipe credit cards without removing them from your pocket...<br />

About This Instructable


306 favorites


Bio: My name is Randy and I run the Instructables Design Studio. I'm also the author of the books 'Simple Bots,' and '62 Projects to ... More »
More by randofo: Bedfellow Robot Bed Easy Science Fair Project Chocolate Blackout Cake
Add instructable to: