Introduction: Small Knex Wheel Lift

Picture of Small Knex Wheel Lift
Hey there, this is the small knex wheel lift I used in my ball machine Dystopia underneath the white floor.
Be sure to read image notes while building along!
I hope you like it!
Be sure to comment, rate and subscribe!
Check out my Website for even more cool stuff!

Step 1: The Base

Picture of The Base

First it's time to make the base

Step 2: Making Some Walls...

Picture of Making Some Walls...

It's time to make some walls! :D
Pay closely attention on how the white rods are.

Step 3: Making Some More Wall Stuff...

Picture of Making Some More Wall Stuff...

Step 4: The Wheel and the Motor

Picture of The Wheel and the Motor

You could use a other motor, you'd have to invent it then on your own.

Step 5: And Some More Walls...

Picture of And Some More Walls...

Step 6: The Exit Track

Picture of The Exit Track

Step 7: Did I Already Mention Walls?

Picture of Did I Already Mention Walls?

Step 8: The Roof

Picture of The Roof

Finally something different! The roof! :D
I show it you like this apart as it is this way possible to attach it all.

Step 9: Finishing It

Picture of Finishing It

You are almost done!
You just have to make sure that the exit floor is already somewhat tilted, what i show here is just that it works in this model, in a ball machine you have to make it tilt somehow different as otherwise the floor won't look good.
So, be sure to comment, rate and subscribe!
And be sure to check out my Website for even more cool stuff!

Comments

guitarshredder123 (author)2012-05-12

ey you should make a small balmachine with instructions with this lift,i'm getting tired of seeing everyone putting lifts on ibls instead of ball machine instructions,
BTW
dystopia is awesome

Haha, thanks! But I think I won't make another ible of a hole ball machine....you should use your imagination :P

ok,
i've played with knex a few years ago,i made some big ball machines back then,how big shall i make them now?

Just do it how you like it :D

wow.thanks.

haha, that was IMO pretty obvious.

this lifty thing works with the newer balls right?

I don't have newer balls so i didn't try out...

Shadowman39 (author)2012-05-04

I see you're still coming out with an Ible every week. :-P Nice lift, but you should have cleaned it up a bit (i.e. the open connectors). Lots of that stuff isn't even needed.

Sorunome (author)Shadowman392012-05-05

Of course i'm coming up with a ible each week :P Did you forget that you talked me into something that made me do it? xD
still have two unpublished ibles and ideas for 20+ ibles (all non-knex realted >:D )

Shadowman39 (author)Sorunome2012-05-05

Haha, I didn't know I talked you into that.

Sorunome (author)Shadowman392012-05-05

You didn't directly do that, you just talked me into doing something different that gave me the idea of doing that ^^

Shadowman39 (author)Sorunome2012-05-06

What will next week's Ible be?

Sorunome (author)Shadowman392012-05-07

Guess :P

Shadowman39 (author)Sorunome2012-05-07

Hmmm... Parallel arm lift?

Sorunome (author)Shadowman392012-05-08

yep! :D
Guess how many pics :P

Shadowman39 (author)Sorunome2012-05-08

200

Sorunome (author)Shadowman392012-05-09

moar

Shadowman39 (author)Sorunome2012-05-09

201

Sorunome (author)Shadowman392012-05-10

not really....
About 400 :P

Shadowman39 (author)Sorunome2012-05-10

That's a lot! How many steps are there?

Sorunome (author)Shadowman392012-05-11

30! :D

jameshond (author)2012-05-04

woooooow this thing is cool

Sorunome (author)jameshond2012-05-04

Haha, thanks!

jameshond (author)Sorunome2012-05-04

Is dystopia take down

Sorunome (author)jameshond2012-05-05

everything except the parallel arm lift :P

jameshond (author)Sorunome2012-05-05

Are you going to make an ible for the pArralel arm lift

Sorunome (author)jameshond2012-05-05

Yeah :P
I'm trying to make it till next Friday :)

jameshond (author)Sorunome2012-05-05

okey coool

KneXtreme (author)2012-05-04

I like it because the ball basically sits on the ground.

Sorunome (author)KneXtreme2012-05-04

Haha, thanks!
And there's a millimeter missing.... :P

About This Instructable

1,772views

1favorite

License:

Bio: You can find me over on Knexflux! https://knexflux.net
More by Sorunome:Knex Ball Machine IcarusHow to add a speaker to your TI-84+Knex Ball Machine Dysphoria
Add instructable to: