Instructables

Step 1: Materials and tools

To make the Bolt puzzle you will need:

A left-handed bolt (For size, look at the picture) and matching nut.
(By the way you can also use a right-handed bolt if you don't have any left-handed bolts, I have used a right-handed bolt and not had any one guess it thus far. However the puzzle will no doubt work better with a left-handed bolt.)
A split washer (Notice that I split it more, see picture).

Tools:
A file for metal.
A saw for metal.
Pliers.
A welder.
A vise.

Optional:
Drill with wire brush attachment.



1-40 of 74Next »
You should make one that can't be opened at all, and one that can. Alternate between giving the dud one out and solving the real one , would it drive everyone crazy ? :o
Mattrox (author)  scraptopower3 years ago
Good idea!
I was skeptical that anyone would fall for this but I had to find out.

I made it with slots that go right over and through the head and a washer that almost makes it possible ( the leading upper edge of the washer and the angle of the slots make the person actually tighten the bolt as they try to get the washer off).

Anyhoo, the results are as follows:

1- 11 Year old girl; solved in 5 minutes.
2- Woman with no real mechanical background; solved in 2 minutes.
3- Male mechanic; gave up after 30 minutes.
4- Another male mechanic; gave up after 20 minutes.

It is very funny watching the disgust they have with themselves as they are told the solution.
Mattrox (author)  FriendOfHumanity3 years ago
Yeah this puzzle is great because to most it is illogical. They look at it and see a bolt welded to a nut, "obviously" the nut will not come off. A mechanic is going to see the weld and imediately assume the nut ain't going nowhere. Whereas someone with less knowledge will try anything.
SenKat3 years ago
DIABOLICAL !!!!! I LOVE it ! I've seen this 'ible a few times and never read it - VERY Glad I read it today, though ! :) Thanks for the entertainment, I cannot wait to try this one out of my Mom and Dad ! Wooo-hooo ! ESPECIALLY my arrogant, "holier-than-thou" Brother ! Muahahahahahaha ! Thank you VERY much - 5 out of 5 !
robosilo4 years ago
this was a funny project. I had funny building it and fun watching people try and solve it. it made for a great stocking stuffer too.
I like this a lot .... I'm making one today.... the notches are very good touch.
Mattrox (author)  FriendOfHumanity4 years ago
Yeah they distract the person doing it. When they look at it they see the notches and immediatly think it is part of the puzzle.
Housedog4 years ago
Really cool! I finally have an excuse to buy that welder I've been wanting for years. Nobody would figure this out, unless by accident.
bobes360 made it!8 months ago

Thank you for posting .. this was my first puzzle I made and I have to say I love making puzzle. Here is picture of my own:

IMG_20140401_162821_361.jpg
c3ralki1l3r2 years ago
could i use jb weld ?
Mattrox (author)  c3ralki1l3r2 years ago
I'm sure that would work. :)
ALogan974 years ago
that's awesome! would soldering work instead of welding though?
it will work fine if you have a nice hot torch
MaXoR4 years ago
What stops a guy from simply twisting the bolt during his attempt to take the washer off? I know the first thing I would do is try to take off the nut, and during that process, what is going to stop me from then accidentally unscrewing it? Especially since you state it's possible for the original person to just twist it off behind their back.

This seems like a game that only works on people with an IQ under 70. So I would find a way to not have the "prey" be able to open it, and WAY MORE important than that is... you MUST have UNIFORM color on the bolt!! Anyone with an IQ over mentally disabled, will wonder why there are two colors. (And if they think far enough that the WELD discolored it, then why would the other side not also be discolored. I think the JB weld would work the best, since it can be hidden better, and won't discolor the bolt sections)
Never learned about heat transfer did you? The other side could easily not be discolored because the bolt absorbed enough heat to keep the other side cool.

If you tighten the nut so that it is not easily removed (but not enough that you can't undo it) then it'll be fine. the weld also keeps people from trying to remove it (looks like its stuck), JB weld would not have as good as an effect.
it looks better when both sides have been fired...it looks uniform and clean
The point is that they see the weld so they wont even try to unscrew it because is WELDED. Your idea of using JB weld is a good idea (not), you should do it and then you can use it on people with an IQ of under 40 that also think is a good idea.
ss3e55 MaXoR4 years ago
That's correct! The person writing this has missed the single most important part of the puzzle....its supposed to be a left handed thread bolt that you start with.

The site where they took the puzzle from explains it properly, and they were nice enough to quote that orign.

Incidentally this seems just like a reprint of that one - albeit with photos of their own model.

Next time they should read the original more carefully and understand the puzzle...obviously without a left handed bolt this is trivial.
arpruss3 years ago
Wow: I had no idea left-handed bolts were so expensive. Fastenal's 1/4-20 left-handed bolts start at about $11.58 .  McMaster-Carr's prices are in the same range.  Has anybody found a cheaper source?
tech dawg3 years ago
this is amazingly clever ....................I LOVE IT!!!:D
one drop of superglue will do the trick if you dont have a welder
Wasagi3 years ago
I really like this idea!
dreamberry3 years ago
My buddy made one of these and left it at my house, I leave it out during parties and watch people go nuts trying to figure it out. It's a good trick, but it's almost reached the saturation point, where not too many people Haven't seen it, around here at least.
jpnagle593 years ago
Nice brain candy...I wonder if Loc-Tight woud work? I was also going to say that you could get a Uni-Strut nut (1") in length, and Loc-Tight to hold the end welded piece, with out having to use a welder. The suggestion of GB weld is a good one.
Cubie23 years ago
Ha! I love puzzles like this where the solution has nothing to do with what everyone thinks it is!!
improyo3 years ago
great idea i made one and no ones guesed it yet....
josht3 years ago
I would really like to make one of these, but I cannot for the life of me find a left handed bolt. Where is everyone getting theirs?
Great puzzle! I made one and my boss still hasn't figured it out. It seems to help that I cut a few different notches on the bolt head, so people keep trying to find the "right" one.
davidpeck3 years ago
I made this for my 10 year old son for Christmas. I didn't do a good job setting up the scenario so he solved it by accident, but he's had a blast foisting it on others. Fun little trick puzzle.
jackatronix3 years ago
surely they would work out that they need to unscrew the nut
and when they do the small piece of the bolt will come off with it
then they can just slide the washer off of the big piece of the bolt
codongolev4 years ago
on the other website, it said to buy a left- hand bolt. that seems to make more sense, because I would think that the first instinct people would have (even seeing the weld) would be to try to unscrew the bolt, which would ruin it.
thats a great idea also. so if they try to unscrew it they are tightening it LOL
nimster643 years ago
the weld is there as a illusion to make the victim think that the nut is welded to the bolt so it can't unscrew and the only way out is through the head of the bolt. that will prevent the victim to try to unscrew it. LOL great Job I must make one
ybilou4 years ago
-- READ THIS--

For this to work, you need to use a left hand bold (reverse thread). Otherwise it is quite easy to unscrew instintively.
I love this! if only i had a welder...
You could drill a hole where the weld would be and put a split pin through instead.
Thats a good idea now i think i might have to make this!
JB weld? Solder? Brazing?
Yeah, thats what i thought too cause im only 14 but the two things i did were either use a oplastic toy bolt and melt it or when i made a mettal one i used epoxy rather than welding
1-40 of 74Next »