Introduction: The Eagle Jet Paper Airplane "you Cannot Hide" ;-)

This is a tutorial for the "Eagle Jet". I have seen it many times before but not on of it has colored Wings.

Here is a short demonstration:



here is a video of me folding the plane:

 

 



Step 1: Take a Sheet of Paper (A4 or Letter)

You can either take a blank sheet or print out the pdf files.

Print tossit1.pdf on on side and tossit2.pdf on the other (of one sheet).
The two "Print arrows" must point in the same direction!

Please do not print it in "Photo" or "High Quality" mode otherwise the paper will get wet and limp so that you can not fold it anymore. Instead print it in "safe Ink" or "economy" or "fast" mode.

I have also made different colors so pick your favored one.

Step 2: Let the Show Begin

If you picked the print version you have to start with the eagles on top (facing up).

Start by folding it vertical in half. Open up again and fold it horizontal in half.

Step 3: Go On....

fold the upper right corner down to the left. The crease should be from the down right corner to the center crease at the top.

Repeat the fold on the opposite side.

Unfold, push at the top of the right corner until the two layers will separate.
line up the creases as sown in the picture.

Step 4: And On...

fold it back together (see pictures)

Step 5: And On...

Fold the upper right corner to the left untill it lines up with the crease you maked at step 3.

Flip over the whole plain. You can repeat the step on the backside now.

Step 6: Crease Again..

Fold in the flap part like in the picture.
Do it again on the frontside.

Now repeat step 3 to 6 for the other wing!

Step 7: Fold a Handle

Now the airplane should look like in the first picture.

First fold in half.

After that make two creases to the left and the right.

Step 8: Last Fold

The rudder is made by creasing the first two layers at the wingends.

Done.

I hope you liked the tutorial, if so please leave a comment.


I am sorry for my bad English!
If you find any mistakes in writing, keep them ;-)

Comments

author
Blackbird17 (author)2009-07-31

i have a faster one should i post it?

author
chandlerd254 (author)Blackbird172017-02-24

yes

author
daniel2023 (author)Blackbird172010-03-01

send me a picture of the papers

author
daniel2023 (author)Blackbird172010-03-01

yes

author
chandlerd254 (author)2017-02-24

I like the tossit blue2 color

author
Aariv (author)2016-09-30

Was tough.how did you pointed the front?i got it flat on the front

author
DeannaA6 (author)2016-01-17

Please add the fold lines to the pdf it would make it SO MUCH EASIER!

author
watkins05 (author)2014-05-22

easy when you print the pdf but hard other wise

author
Dfootty (author)2012-10-14

seriously, TOO HARD? this is a simple design
a good one too

author
ppanchal1 (author)2012-05-01

it is cool
i used a blank sheet & custom painted it

author
ppanchal1 (author)2012-05-01

it is cool
i used a blank sheet & custom painted it

author
theswordninja561 (author)2011-03-12

could u clarify step 3...stuck on it

author

I uploaded a Video of the foldings!
I hope it is clear now.

author
jsuperfine (author)one-lightbulb2011-08-06

Where do u click to get it up?

author

what do u mean?

author
saransaleen (author)2011-04-30

hey am i supposed to print all .pf files ? pls reply

author

You can also take a blank page.
If you like my design print two Pdf on one sheet.
Refer to step 1.

author
miggythepiggy (author)2010-11-27

its a thunder bomber

author
paper magican (author)2010-02-24

looks kinda hard
 

author
naruto31719 (author)2009-12-01

a little too hard

author
jmusick (author)2009-04-07

I don't understand push at the top of the right corner until the two layers separate. This is just not clear. Can you help me? craftyj

author
Kaiven (author)2009-03-20

Flies very nicely with a paperclip. Kinda hard to throw right, but flies nice.

author
theswordninja651 (author)2008-12-27

i can't make it.

author
freakinslop (author)2008-05-17

unclear but looks kool

author
dnadna (author)2008-04-30

this is the best paper airplane i ever flew! it went strait for 16 feet. i added a paper clip to the front and bent both bottom and top flaps at 45 degrees faceing outward. +1

author
hiue (author)2008-03-05

i messed up and dont know ho wto do it... its unclear to me

author
Top Dog (author)hiue2008-04-09

same here...

author
Top Dog (author)Top Dog2008-04-09

looks cool though :-D

author
GorillazMiko (author)2008-03-03

That's cool! Just realizing, my paper plane thing is the first one related to yours. Anyways, wow, nice job, it looks really nice, the detail and everything. Looks like a perfect glider, hopefully I will try this out!

Voted.

About This Instructable

67,260views

42favorites

License:

More by one-lightbulb:SpongeBob SquarePants Snow Sculpture in ColorTea light lantern with customizable printing.The Eagle Jet Paper Airplane "you cannot hide"  ;-)
Add instructable to: