Instructables
Picture of Tree House Bed
DSC_0036.JPG
Kids love a cool bed.  Somewhere to not only sleep, but to also play.  A lot of the "cool" beds on the market are either basic beds with Cartoon Characters on the sides, or enclosed forts which are difficult for big people (i.e., the parents) to get into.  There are some really neat custom beds out there, but they go far beyond a weekend project and require serious skill and money.  The tree house bed was designed to be friendly to both the kids and their parents. Kids love tree houses, sleeping outside, and climbing.  This bed channels that.  It's also open, so parents can look in, and crawl in without too much trouble.  Due to the materials it's made from, its pretty budget friendly as custom furniture goes.  The bed was designed to look more like a tree house more than a piece of furniture.  To accomplish that, it's built it with materials and techniques that are used to build decks and real tree houses.  Since you will be looking at it up close, a few liberties were taken to give it a bit more polish.  It helps to have a few less common tools, (e.g., router, pocket hole jig) but It can be built with the basic tools any good DIYer should have in his or her arsenal.

Materials:
2 x 4
2 x 6
2 x 8
2 x 10
4 x 4
Deck Screws
Pocket Hole Screws
Polyurethane or Polyacrylic to finish

*Do not use pressure treated lumber or cedar. 

Recommended Tools:

Circular Saw
Table Saw
Jig Saw
Pocket Hole Jig
Drill
Power Sander

Useful Tools:

Radial Arm or Compound Saw
Dado Blade
Router
Impact Wrench / Driver
Counter-sink Bits

I didn't provide a the number of boards that you'll need, since not all boards are the same.  A 8'  2x4 will give you two 3' boards, where you might squeeze four out of a 12 footer.  However, when you get to the lumber yard, you might find the 8' boards are in much nicer shape than the 12' ones.  It might also be cheaper to buy two 8' boards than a single 16', so I'll leave this to you to decide what to buy based on quality and price available.  What type of wood you buy is largely a matter of personal taste.  However, I will say do not use pressure treated wood, even if you have a bunch laying around.  Most of you know this, but pressure treated wood is pretty toxic.  It's toxic to the touch and off gasses into the air.  I wouldn't rely on a finish to make it safe either.  Just don't use it for this project.    

The list of tools is also just just a suggestion, there's many ways to accomplish the same thing.  I personally used all the tools I listed. You could probably get away with just circular saw and drill, but I wouldn't recommend it.   
 
Remove these adsRemove these ads by Signing Up
dpurcell44 months ago
Awesome bed design!! Wow!
cmiller611 year ago
About how much does this cost to make?
matt10nick (author)  cmiller611 year ago
I don't remember. I want to say it was in the low $100s range. Assuming you have all the tools you need, there are three big line items. 1) Wood, 2) polyacrylic, 3) Screws. Wood is the major item, and it will vary some what place to place. If you can figure out how much you need of each board, and then see what your local lumber yard sells it for. If your going for the lowest price, compare the cost of 8', 12', and 16' boards. Sometimes, two 8' boards are a better deal than a 12', and sometimes not.
Mamohau1 year ago
"Kids love a cool bed"? What about adults?? I think it's brilliant and I'm planning on making this out of pallet wood for myself. Just planning the planing/sanding method as bit more required than usual!
We absolutely want to do this, but we have a bit of a puzzle. Our son will outgrow his current bed within 5 months, but we won't have enough money saved to rip out all of our carpeting for about 2 years.

So after we build it, we'll need to take it down and put it back up after the engineered hardwood goes in.

Would that change the plan? The hardware? We plan to use whatever we can afford in the Toyota Camry or Honda Accord of hardwoods.
BtheBike2 years ago
used google sketch-up ?
matt10nick (author)  BtheBike2 years ago
Yes, I did. I use Sketch-up for almost all of my furniture to try to get the dimensions and perspective down.
chelma12 years ago
picture a pink and purple castle drawn on the wall and the bed also. Could be for a princess or a prince depending on colors. Mossy Oak Camo for the boys.
Great idea and a cool hiding place underneath.
Excellent instructable, the illustrations are a great touch! Wish I had a kid to make it for!
My son would be very glad if you'd make this for him! :)
quakefiend2 years ago
Nice!! this design makes it easy to raise it up so the space underneath could be a usable area as well (maybe integrate a desk into the 4x4s). Great instructable, I'm liking your method of building the railing.. very solid.
PuffinEM2 years ago
I love it! But I do have a slightly unrelated question. Did you also make the dresser?
matt10nick (author)  PuffinEM2 years ago
I assembled it, but that's all I can claim. It came from Ikea. It's part of their STUVA system which is pretty neat. They sell different size boxes and then you can fill them in with what you want. I could have done all big drawers, two big and four small drawers, or taken drawers out and replaced them with shelves. The boxes are all white, but the drawer / door fronts come in green, blue, and pink in addition to the natural.
Great plan! I've got something similar in mind for my son's room.
CrLz2 years ago
A sweet bed!
That's awesome! Love that it looks just like a deck. :D