USB Rechargeable Flashlight
3 Steps
In this instructable I will show you how to make a flashlight that charges within seconds and lasts for about one hour. All with USB! Please tell me about how I am doing on this Instructable. This is my first. Thank you. A while back Trialex posted this instructable. His instructable gives calculations if you need them.
Remove these ads by Signing Up

The parts you will need are

1. A 1 farad 5.5 volt super capacitor

2. A male USB connector. (You can cut a USB adaptor and use only the red and black wires or + and - connections

3. A normally open push button switch

4. (Optional) A toggle switch

5. A perf board or etched circuit board

6. A Led any LED works as long as it is not above 4.5 volts. Preferably with built in resistor. You can also use this color changing LED

7. A resistor if your led does not have one.

8. Wires if you are using a perf board

9. A usb charger. (You may be able to use a computer USB port but I don't take any responsibility for any damages to your equipment.)

Most of the parts can be bought from http://allelectronics.com. They have the very best prices that I have seen so far.

Mike Nelson says: Oct 1, 2010. 4:19 PM
so im trying to figure out what kind of super-cap i need to power an led flashlight for an hour. i tought the idea was 1F = 1 Amp/second, so if you drew an amp, it would run out in a second, but if you drew 10 mA, you would have power for 100 seconds.

if you're saying this will last for ~hour then my formula doesn't jive well. Am i missing something else here?

1 hour = 60 minutes = 3600 seconds,

1000ma / 3600 = ~.30 mA per second. i don't know any LED's that will light up at all with that little current...

thanks!
Adam Manick (author) says: Mar 5, 2012. 12:13 PM
Also, this is a 1 fared capacitor at 5.5 volts. This LED only draws about half of that at about 3-5 mA. The LED also dims quite a bit after about a half hour.
Broom says: Oct 5, 2010. 3:47 PM
"Low current LEDs" can operate at currents below 5mA, although most of these are red.
Adam Manick (author) says: Oct 3, 2010. 8:18 PM
How long it lasts depends on the led and resistor you use. It also depends on the charge time. For me after about a half an hour the led gets quite dim. If you use a larger resistor the led will stay on longer. You can also try building a joule thief or a D.C voltage booster to light up a low current led for a longer time. A neon lamp requires very little current so if you boost the voltage high enough you may be able to light it up for quite some time. Thanks for the reply.

Can everybody please rate my instructable so I know how I am doing. Thanks.
iApple guy says: Feb 25, 2012. 9:46 PM
If I were to add more caps I parrerell would it last longer, or a cap with more ufs then just one uf?
Adam Manick (author) says: Feb 27, 2012. 4:49 PM
Yes, but I believe that if you wire the capacitos to gain a higher capacitance, the the voltage will be cut in half.
ideeman1994 says: Feb 29, 2012. 12:50 PM
Actually, if you wire them in parallel, you'll add up capacitance without any voltage loss ;)

The problem will appear if you wire them in series: you'll surely have more voltage, but here the capacitance will be hugely reduced...
Adam Manick (author) says: Feb 29, 2012. 9:54 PM
Thanks for clearing that up. I didn't realy remember which way it went. Thank you for reminding me!
iApple guy says: Feb 25, 2012. 9:38 PM
I have a question is a supercapacitor a electrolytic capacitor?
Adam Manick (author) says: Feb 27, 2012. 4:46 PM
Yes it is. :)
juanangel says: Feb 3, 2011. 5:21 PM
Great idea.
Have you thought of replacing the capacitor with a CMOS baterry? Little changes in the setup and will last a lot longer and can add another LED. What about a picture of the backside. With a 1 foot long cable can be used to light the keyboard while connected to the laptop.(for those times you are in bed and do not want to disturb your roommate). Once encased, just push the cable inside of it with theplug, Both will be protected at the same time, more transportable,
Adam Manick (author) says: Apr 26, 2011. 4:48 PM
Great ideas. Unfortunately I do not have a CMOS battery and do not know where to get one. If you decide to try it I would love to see the pictures. Thanks!
vangie says: Feb 25, 2011. 6:43 AM
hi....why does the push button switch did not include in the schematic diagram??? tnx....
Adam Manick (author) says: Apr 26, 2011. 4:45 PM
I think you mean the toggle switch. I built the diagram before I made it. So I came up with the idea to have the toggle switch while building it.
Adam Manick (author) says: Apr 26, 2011. 4:43 PM
Thank you! Did you build it?
atul adrian says: Apr 23, 2011. 1:04 AM
I loved it.It was excellent and so easy also.
trialex says: Oct 4, 2010. 9:23 PM
No reference to my existing project from 4 years ago?

http://www.instructables.com/id/Battery-Free%2c-USB-Powered-LED-Torch/

I even do all the calculations for you to work out charging and use times!
Adam Manick (author) says: Oct 5, 2010. 4:48 PM
I used your instructable as a reference for the calculations people may need.
Wesley666 says: Sep 13, 2010. 3:08 PM
You can do this exact same thing with Polyacene Batteries. They are a bit smaller, hold a bit of a longer charge are cheaper then super caps, but take a little bit longer to charge. Generally they are used in Cellphones for memory backup, but you can find them on the internet for 1000 for \$50. Still, cool Ible! :)
Adam Manick (author) says: Sep 13, 2010. 4:13 PM
I should try that sometime. I just made this Instructable because this is what I had on hand and this charges a bit faster. I would like to try this with batteries sometime but do they need a circuit to charge? If you have any info on them please post me a link so I can try it. Thanks!
Wesley666 says: Sep 13, 2010. 5:59 PM
I don't think they need a circuit, they just plug into a power source with the same voltage as them, and they charge, so it may require a small circuit, but not much...
Adam Manick (author) says: Sep 13, 2010. 9:04 PM
OK thanks for your help. By the way I read your Instructables and they are really good. I want to build your touch switch once I get the parts.
rockyt says: Sep 13, 2010. 9:33 AM
Cool. I'm going to make some.
Adam Manick (author) says: Sep 12, 2010. 11:08 AM
I appreciate your help. I went right ahead and fixed that. Normally I would catch something like that.
sw says: Sep 12, 2010. 8:28 AM
In your circuit diagram, the polarity of the LED is reversed: the pointy end (Cathode) needs to point to the negative side.