Instructables
This is instructions on how I built a Van de Graaff generator from junk lying about my house.(And I do mean junk.)
 
Remove these adsRemove these ads by Signing Up

Step 1: Parts

Okay, the first thing you will want to do is gather all of the necessary parts. They include 1 pencil with ereaser, two dried out old click pen parts, a piece of 8in. long PVC pipe, 1 dead light bulb, 1ft long piece of 2 by 4, a elastic band, one metal paper clip, aluminum foil, see through tape, one small toy motor, 9 volt battery, and some junk wire. A good sense of humor and a few band-aids would come in handy too.

Step 2: Part 1

The first step is to take your 1ft piece 2 by 4 and drill 1in. deep with a drill that is wide enough to snugly fit your PVC pipe. The position where you drill the hole should not really matter just as long as there is enough room to work with.

Step 3: Step 2

The next thing you do is stick the PVC pipe into the drilled out hole, and mark the point where the axel of your motor touches PVC pipe and drill a (STRAIGHT) hole through both sides of the PVC.Then drill another (STRAIGHT) hole through both sides of the pipe at the point were your elastic band is lightly out stretched. Make sure that elastic band is not too tight or it will stop the motor.

Step 4: Step3

Next you drill two more holes into the PVC.The first hole should be drilled directly perpendicular too the bottom holes, and should only go through one side of the PVC.The second hole should go just above the top hole and should also be drilled through only one side of the PVC.

Step 5: Step 4

Now you need to clean out any ink that is left in the dried out pen parts. I used a ribbon tie like the ones that come with trash bags to clean out the pen.
1-40 of 315Next »
SgBriggs1 year ago
dose the grounding wire need to touch the ground or the - terminal on the battery or a wand so you can do the lightning stick thing?

The bottom wire needs to touch the belt, with the other end grounded, either with your hand or actually into the ground

Where the bottom brush has to be attached?

Bro just drill a small hole below the motor..and attach the bottom brush near the bottom roller(where the motor is).....i mean the bottom brush should be very near the bottom roller......just like u did in the upper roller :D

Georgewister4 months ago

You are brilliant!

I hope you will make more instructables.

I discovered the perfect matiaral. take one of the big capacitors in microwave open it up in side there is pieces of thin foil covered in a plastic in between is is them is the perfect martial.
get your english corrected
good job
dng81 year ago
here's another website from MAKE http://blog.makezine.com/projects/simple-van-de-graaff-generator/
marvel_x231 year ago
what can be used instead of the pvc tube
scristian1 year ago
i made a shake machine :(
scristian1 year ago
Does it still work if i use 1 engine on the top roller and one on the bottom one?
also i covered the top roler with somme duct tape so that the ruber band stays centered.

PS:for somme reason mine doesn't do anything other that shake
Velin91 year ago
also can you use a plastic straw instead of the pen tube?
Velin91 year ago
Can you use a piece of foam for the base instead of the wood or not?

btw this looks like a very cool project. good job.
_
( ((
\ =\
__\_ `-\
(____))( \----
(____)) _
(____))
(____))____/----
Thumbs Up
Does it actully work?
Check out www.physicsplayground.com for extreme Van de Graaff generators!! Its a must see!!
how thick pvc?
CoolDon2 years ago
and if we attach a 9 volt battery to a toy motor wont it burn?
CoolDon2 years ago
Hey can we run something on this one because i need to do it for ma science fair project
swaghmare2 years ago
where does the another end of the bottom wire go????
plz reply fast.
Its a ground wire i think so!
Aron3132 years ago
Do you have a video on it?
video please
can anybody plz send me the pdf file for it?
i need it urgently as m havin an exhibition in school.

Thanx :)
KronoNaut7 years ago
Am I assuming correctly that you attach the top lead to the aluminum foil, and not the metal part of the bulb?
Yeah, connecting to the metal of the bulb would just attach to the filaments, however, what we want is charge to build up in the foil sphere outside.
maryamyam2 years ago
is the top wire attached to BOTH the light bulb and the upper rubber band?
SCIENCEPAL2 years ago
Nice project for a science fair!!!!
Tobor 2.03 years ago
Can you leave out the bottom wire? I want to know the point of the bottom wire.
the bottom wire is to keep the generator grounded.
builder232 years ago
I REALLY need to know if this generator works. i am doing a science fair project on electrostatic electricity, and have already tried to build one of these from another website. Somebody please respond!
rocketbat7 years ago
LOL!" super size it and send your neighbors annoying cat into the next century" that is just what i intend to do!
Been there.
Done that.

=D
You could also send your neigbor with them!   >: )
eric m3 years ago
photography here is awful.

how bout some closeups of the comb and pulley.
does it have to be PVC? or could the tube be Cardboard or something else thank you :D
Hi,
Can u plz tell me how much volts will this generator produce?
and one more question if it produces high voltage then why can't we use it for electicity supply for home.
waiting 4 reply.
Thnx
-Jerin
because this needs a motor, I think it produces electrostatic energy.
thank you
tecnokid3 years ago
why do we have to have a burnt lamp instead of a working one
1-40 of 315Next »