I'd like to start off this hulk by telling the story of the Vivisector. Originally, It was but a giant, 60 shot wheel. Then, I got the idea to make it back mounted. I built a casing that wasn't nearly strong enough. I built another. And another. I ended up wasting an enormous amount of my pieces on the shell. But here it is, in all its glory - the Vivisector.
This Instruction will be in 9 parts - The Wheel, The Bullets, The Motor Cage, The Back, The Base, The Sides, The Front, The Top, and The Attachments.
Gray Rods: 131
Red Rods: 312
Yellow Rods: 733
Blue Rods: 1385
White Rods: 240
Green Rods: 543
Flexi Rods: 0
Total Rods: 3344
Blue 3D Connectors: 685
Purple 3D Connectors: 795
White 8-Slot Connectors: 87
Yellow 5-Slot Connectors: 330
Orange 5-Slot Connectors :0
Green 4-Slot Connectors: 2
Red 3-Slot Connectors: 6
Orange 2-Slot Connectors: 254
Gray 2-Slot Connectors: 125
Gray 1-Slot Connectors: 286
Tabbed Connectors :64
Black Y Connectors: 5
Green Crossties: 0
Total Connectors: 2639
Silver Bearings: 20
Blue Bearings: 40
Chain Links: 0
Total Other Parts: 122
Total Parts: 6100
Step 1: The Wheel/Bullets I: Overview
Anyway, Piece count is as follows...
Gray Rods: 102
Red Rods: 102
Yellow Rods: 204
Blue Rods: 60
White Rods: 76
Green Rods: 112
Total Rods: 656
Blue 3D Connectors: 120
White 8-Slot Connectors: 14
Yellow 5-Slot Connectors: 160
Orange 2-Slot Connectors: 184
Gray 2-Slot Connectors: 120
Gray 1-Slot Connectors: 256
Total Connectors: 915
Silver Bearings: 2
Blue Bearings: 1
Total Other Parts: 3
Total Parts: 1574
+60 Rubber Bands (#32, Doubled Up)
Step 2: The Wheel I: The Core
Step 3: The Wheel II: The Spokes
2: Build 64. These are singles
3: Build 24. These are doubles.
Connect singles to 1,2,4,6 and 8,9,11, and 13 (Grey facing towards center)
1,8 2,9 4,11 and 6,13 are all pairs.
Connect doubles to 3,5,7 and the other sides to 10, 12, and 14, respectively (Grey facing center)
Step 4: The Bullets
And 4 modded with grays and whites.
Arrange them like this
1mod - 14regular
Keep going and you'll have 4 of those.
Now, attach them in a huge long line.
Get the wheel out again and attach in the following formation. Attach the SECOND Bullet(The first is modded) to the very top - any of the top 8 spokes. Attach the others sequentially, but SKIP the Modded bullets. In the end, you have 56 attached, 4 free.
Make sure the side the bullet comes out of has the two spacers, and the other side has the 3 spacers and white connector.
Alright, the wheel is done. If you just want to build this, you're done too.
Step 5: The Motor Cage I: The Motors
Anyway, Build these and put them somewhere.
Step 9: The Motor Cage V: Assembly
Then, add a blue spacer and Gray connector.
Add the Gears...
And the Motors
Step 10: The Back I: The Core
Step 13: The Back IV: Expanding Borders 2
Put them all over like in pic 3.
Add red rods like in pic 4.
Build 4 of pic 6.
Build 8 of pic 7.
Then insert steps 10-12.
Step 15: The Back VI: Expanding Borders 3
Build pic 11.
The back is done.
Step 19: The Beefy Base
Step 23: The Front IV: Expanding ther Borders 2
Step 25: The Front VI: Expanding the Borders 3
Step 26: The Front VII: The Border 3
Now you have a pretty Octagon.
Step 27: The Front VIII: Expanding the Borders 4
And at the bottom, reds too.
Step 28: The Front IX: The Borders 4,5,6, and 7
Step 29: The Front X: Bonus Panels
...Or don't add them at all. They're there just 'cause they look cool.
Step 31: Assembly
Step 32: The Wiring
Anyway, tie it around The orange piece a few times. Then add that red part. Then tie it around the edge and add a white rod. Then loop it around the top, and pull it down to the base.
Step 33: The Attachments I: Bottom Armrests
Step 34: The Attatchments II: Shoulder Rests
Step 35: The Attachments III: The Chestplate
Step 36: Loading
Watch the video to see how to do it fastily.