Introduction: Xbox 360 Rumble Powered Rapid Fire Mod

Easy way to mod your xbox 360 controller without all the fancy microchips and is still undetectable
(SO FAR).

(I AM NOT RESPONSIBLE FOR ANY DAMAGE DONE TO YOUR CONTROLLER DURING THE MODDING PROCESS----CONTINUE AT YOUR OWN RISK)

SORRY ABOUT THE PICTURE QUALITY MY CAMERA ISN'T THE BEST

Step 1: MATERIALS

T8H security tool
Sauter gun
sauter wire
sauter paste
momentary push button (x1 per controller)
18 Gauge wire (x2 per controller)
MAKE SURE YOUR CONTROLLER HAS THE BLOCK RESISTOR SHOWN IN THE PICTURE AS A LITTLE SILVER OVAL SHAPED BLOCK IN THE MIDDLE OF THE CONTROLLER FOR THIS TO WORK

Step 2: DISSASSEMBLEY

1] Take out the seven screws using your T8H security screwdriver
2] Pull of the back (the front of the controller should be face down)
3] Gently take of the chip board and turn it over so the thumbstics face up
4] Remove both rumble packs or just the right rumble pack (little motor hanging from bottom of chip)

Step 3: SOLDERING THE CONNECTIONS

1] Solder 1 of your 2 wires to one side of the button and the other wire to the other peg -DO NOT LET THE TWO WIRES OR SAUTER TOUCH-
2] Solder the other end of one of the wires to the middle prong just under the A button kind of like this
.
.
.

3] Sauter the 2nd wire to the right of two prongs side by side just underneath the first 3 prongs
EX
.
.
.

. .

{BE SURE THE WIRES ONLY TOUCH THE MIDDLE PRONG AND THE RIGHT PRONG THEY SHOULD NOT BE TOUCHING ANY OF THE OTHER PRONGS}

Step 4: DRILLING THE HOLE

1] DRILL A HOLE TO FIT THE BUTTON YOU BOUGHT ON THE BACK OF THE CONTROLLER IN THE POSITION SHOWN ON THE SIDE OF THE CONTROLLER YOU HOLD WITH YOUR RIGHT HAND

Step 5: INSERTING THE BUTTON

IF YOU DO NOT PUT THE HOLE WHERE I SHOWED YOU THE BUTTON WILL NOT IT UNDER THE CHIP BOARD

PLACE THE BUTTON IN THE HOLE AND HAND TIGHTEN THE NUT ON THE BUTTON

IT SHOULD BE A COMFORTABLE POSITION FOR YOUR RIGHT HAND MIDDLE FINGER OR RING FINGER

Step 6: GUIDELINES FOR MY SAFETY AND CONTACT INFO. AND MISC. INFO

1-ANYTHING THAT HAPPENS TO YOUR CONTROLLER IS NOT MY FAULT AND I CAN NOT BE HELD ACCOUNTABLE FOR IT

2-IF YOU GET KICKED OR BANNED FROM XBOX LIVE SERVERS IS NOT MY FAULT

3-NEW UPDATES FOR CALL OF DUTY 4 AND WORLD AT WAR HAVE LIMITED THE SPEED OF THE MOD

4- CAN BE USED IN HALO 3, BATTLEFIELD 1943, CALL OF DUTY 4, MW2, CALL OF DUTY WORLD AT WAR, RAINBOW SIX VEGAS 2 AND NEARLY EVERY OTHER FIRST PERSON SHOOTER

5- I DO NOT USE MY MOD FOR ONLINE PLAY BECAUSE I DO NOT BELIEVE IN CHEATING ONLINE WHERE PEOPLE HAVE TO PAY TO PLAY


THANK YOU FOR TAKING THE TIME TO READ MY INSTRUCTABLE AND HAPPY GAMING

NOTE****1-25-10 WORD AROUND IS MICROSFT IS BANNING MODDERS FROM ALL SERVERS IF FOUND---PRECED AT YOUR OWN RISK---I HAVE NOT BEEN BANNED YET OR SEEN ANYONE WHO HAS CONTACT ME ON THIS INSTRUCTABLE IF YOU HAVE MORE INFO. THANK YOU

Comments

author
blaze.ninja42.0 made it! (author)2013-01-30

and it has to be on the front of the controller? (crystal oscillator) i have two wireless controllers, both different inside, neither one has that thing on the front but they both have it on the back.

author
ikent1 made it! (author)2011-08-15

What size bit thought?

author
blaze.ninja42.0 made it! (author)blaze.ninja42.02013-01-25

torx T8H is the size lol

author
lloydrmc made it! (author)2012-10-08

Could be that "resistor" is really a crystal or an oscillator module.

author
TrueGent made it! (author)2012-07-29

http://www.mspointscodes.com/?i=1424702

author
ikoons made it! (author)2011-08-23

anyone know how to mod a controller without the little silver oval?

author
alindsey3 made it! (author)alindsey32012-07-01

its called a crystal oscillator :) what type of controller do you have new or old?

author
cdombach made it! (author)2012-05-09

http://www.mspointscodes.com/?i=1086288

author
griizzly made it! (author)2011-01-05

does this work for gears of war 2? i tried to do it to my controller and it just goes mental any help would be apprciated. i connected the wires right and and made sure they dont touch but i cant use my right trigger at all and the thing just has a mind of its own. could you tell me how your supposed to use it and maybe any ideas as to why it isnt working for me? thank you

author
Termn82r made it! (author)Termn82r2011-01-05

check the push button you used. If the button is a CLOSED connection when you press the button you will stop shooting. Make sure the button you hook up to the controller is a OPEN connection so therefore in order to close the connection (fire your gun) you have to press it. :)

Hope this helps!!

author
ikoons made it! (author)ikoons2011-08-23

can you tell what kind of button you have just by looking at it?

author
ol987986 made it! (author)2011-03-13

why not just buy a third party one for like 20 quid?

author
HOTBEEMINBOY made it! (author)2011-03-10

noob

author
griizzly made it! (author)2011-01-07

wow i think it should work now, i bought the ones that are normally closed haha thanks for your help hopefully itll work for me now

author
Shotsking77 made it! (author)2011-01-02

Does this work on call of duty black ops?

author
Termn82r made it! (author)Termn82r2011-01-03

Yes and might I add it is amazing for zombies!

author
RDSawicki made it! (author)2010-12-22

u don't no how to spell solder or in ur cause sauter lol

author
hobojoecs made it! (author)2010-09-08

Look dude thats not a resistor block its a crystal oscillator, which is for clock signals... lol just so you know

author
techmaster96 made it! (author)2010-07-23

would it help if you cut off the half wheel thing on the moter so it could spin faster thus faster shooting

author
Termn82r made it! (author)Termn82r2010-08-07

i found that by removing the rumble pack (motor) completely it causes the mod to shoot faster... you could leave the motor on but its not required and it just gets in the way for me...the motor should pull right off of the plugin no problem just be gentle with the plug in and the circuit board

author
brokenwings666 made it! (author)2010-05-28

Your pictures are way to blurry. You need to take better photos for this. I had to look somewhere else to find out how to do this on account I can't see anything. Just some friendly advice ;). Take care and happy modding.

author
Termn82r made it! (author)Termn82r2010-07-01

Thank you im aware if that as i have apologized in my last page of the instructable for the poor quality of the pictures because my camera isnt the best

author
max0506 made it! (author)2010-06-28

what camera do you use jeze

author
Termn82r made it! (author)2010-02-16

As long as the game you are playing has vibration enabled the mod will work regardless of quadrant thats lit up

author
hiphopapotomas made it! (author)hiphopapotomas2010-03-31

 nice mod i did this but its not as fast as i would like for the FAL or the pistols, but the snipers are super fast

author
Termn82r made it! (author)Termn82r2010-04-01

yes the snipers are very fast and thats a plus especially if you fire in short bursts. Try adding a silencer to the FAL and pistols (especially the usp .45) and that increases the rate of fire and speed of the modification.
Also you can use for the FAMAS, M16, and M93R to keep firing instead of pulling the trigger after each 3R burst

author
plasma dragon007 made it! (author)2010-02-14

I liked this method over the one of soldering it to the LED.  Too easy to burn out an LED if you screw up... I did that to one of mine X_X

Plus, this should work regardless of what player quadrant is lit up, right?

About This Instructable

22,388views

11favorites

License:

More by Termn82r:Xbox 360 Rumble powered rapid fire mod
Add instructable to: