YAN9VUSBC

(Yet Another 9 Volt USB Charger)

Step 1 Parts and testing.

PARTS:

5v regulator (Lm7805)
Female USB port
Resistor
LED
Braided wire (20g)
Used 9v battery (Walgreen's brand)
5 minute liquid epoxy
Non-conductive epoxy putty

The circuit design is from http://ipod.hackaday.com/entry/1234000270029372/ All I did was add an LED so I could see if the battery was good. He's got nice diagrams of the USB and regulator to help you wire this together.

Comments

[Pranjal Joshi]

i think it wil damage cell phone coz cell phone need 4 volts and it supliies 9v??
can resistors decrease the voltage?
please rply someone

[kumaran512]

7805 ic is used so u ll get only 5v......so no harm to ur phone......

[iApple guy]

The regulator drops the voltage down to 5vdc, and actually phones and USB devices need 5vdc, not 4.

[tutdude98]

5v regulator (Lm7805) drop voltage to 5v

[Pranjal Joshi]

i made a project same to it..
but aftr charging my cellphone shows "bad contact of charger".. so wat can i do to repair dat??

[tutdude98]

change the usb cabel or check the output voltage

[Pranjal Joshi]

i chkd usb cable..
der is no fault..
n i nt yet got a multimeter to test output voltage.. :(
did u mean for 1st few mins. the voltage is more than 5v bt den it decreases below the minimum charging capacity of battery hence it shows bad charger contact????
if yes then wats the solution on it..

[kumaran512]

nice cover idea...........gud job

[nodoubtman]

i think that doesnt work for a ipod touch 4 G?

thank you!
marC:)

[mm3814]

it would work for an iphone right

[Dalton63841]

It probably could, but I would not recommend it. That 7805 regulator is rated for 1 amp, and is going to get dangerously hot, even with a heatsink, burning off 4v of power to regulate 9v down to 5v. Not to mention that a linear regulator is TERRIBLY inefficient in this particular instance. A better option would be a switching regulator such as this one:
http://focus.ti.com/lit/ds/symlink/ptr08100w.pdf

The switching regulator is still extremely small, and would easily fit if you left the casing only slightly longer. Also, switching regulators don't burn off the excess voltage, but instead use pulse. By turning the flow of current on and off VERY quickly, it simulates lower voltages. A linear reg gives you about 55% efficiency, whereas the switching reg gives you close to 90%, which means that battery will last longer also. Not to mention the added safety because that switching reg is rated up to 10 amps.

[Damian James]

USB is only supposed to be able to supply 500mA. I can understand going up to an amp, but 10A?

[Dalton63841]

The USB port on a computer only supplies 500nA. The cords can usually handle much more than that. Also, its, up to 10A, but it won't ever be that high. The circuit only pulls what it needs.

[Matrix-technician]

Actually i have made several of these for myself. The regulators I use are Radio shack 7805: +5vdc 1 amp. Even though these are rated up to 150 degrees celcius, mine stay cold to the touch after hours of use. They also incoporate internal overload protection as well as short circuit current limit. So these thing will fry themselves before they can damage your device.

[mrcolortvjr]

I'm making this for an iPhone 4, so I'm using this regulator instead, because of a previously made comment. What grade of resistor do I use?

[sanyo8088]

can it charge a psp

[TigrisLi]

Can it charge a Iphone 4??

[neodymium]

This one will not charge the iphone4, but this one will: http://www.instructables.com/id/Make-a-USB-iPhone-iPod-Charger-On-The-Cheep/ basically the same thing but in an altoids tin and outputs 2V across the data pins. this one will also work with any other usb charged device like the one in this instructable here.

[taylorglenn]

it won't charge iPhone 4. The iphone 4 requires 2.2vdc across the D+ pin of the USB connector and 2.8vdc across the D- pin. Otherwise, it will not charge.

[TigrisLi]

Ok, thanks!

[mrcolortvjr]

this is untested but i believe (from a bit of research) that if you use 2 2200 mA resistors it will charge the iPhone

[tutdude98]

ok can i use instead 9v battery , 4*1,2 V rechargeable batterys ? if i use will i need 5v regulator

[BeefyHaze]

I admire the fact that you made something useful regarding usb's...

I just went through 50 pages of instructable usb ideas that all revolved around sticking a usb drive inside of some half-### enclosure.... Thank you for making a real usb instructable that serves a purpose.

[throbscottle]

This is cool and I like it - can you do one for us where you dismantle the battery's insides and use 1 or 2 of the cells, instead of having an external battery? You could use a joule thief type circuit to boost the voltage. Guess you'd need some way to change the cells though. Duh. Just thinking aloud....

[amacias-1]

Good tutorial, i did and it is work ok. thanks

[tave]

if u have a psp slim..u can charge from the usb port

[courlander]

only in usb mode

[wout smeets]

no you need a special cable

[beehard44]

no you don't

[wout smeets]

if u wana charge it with te normale cable u need connection with the pc


u need this http://www.game.co.uk/Accessories/PSP/Cables-and-Adapters/GAMEware-PSP-USB-Link-Charger-Cable/~r326193/

[GENERALCHAOS]

pspGO
problem solved

[uhsnamih]

i got a portable charger and my psp 3k works just fine, when i hook up my usb cable with it

[T-virus]

Could you post the circuit here? Your link was broken.

[freakyqwerty]

Is it me or does the title not tell what the instructible is...

[fogman103]

I think it satnds for Yet Another 9v USB Charger.

[freakyqwerty]

I know-it says in the first step I just mean when your searching the site…

[Matrix-technician]

What type of resistor do i need? Also, i would apreciate it if you could list the specs of the resistor so i know which one to get.

[DoctorOfAwesome]

Were do i get a regulator?

[charlie.nourse]

Radioshack

[codongolev]

ebay is a great resource.