Step 5: Put it all together!

now just drill the holes and install all of the parts in the tin, be careful not to scratch up the sides like I did, and have a good plan for the layout before you start to poke holes in your tin
Thank you for the guide, but I found a much simplier solution to MY problem. I let my psp get completly out of juice, and I couldn't find the charger. So, I go online to find some re-charge solutions, and I foung this. I then dug through my old &quot;spare parts&quot; bin. And I found a 5v cell phone charger. So I took the Mono cord, and just soddered the two together. But I think you for your guide anyway.<br>
Interesting, but unrelated little fact, that may already be well known: The fumes are more or less adhering to the oil in your fingerprints, so that cloudiness is palm/fingerprints, I think members of law enforcement use similar methods to get fingerprints off of 'strange' surfaces
would it be possible to buy this or one off you?<br /> <br /> here is my email<br /> <br /> <a href="mailto:oldwiseblack-1234567@yahoo.co.uk" rel="nofollow">oldwiseblack-1234567@yahoo.co.uk</a>
I know this is an old 'ible, but I thought that I would say that the reason that it is around &quot;4.7 volts&quot; is because with voltage regulators need about a 2 volt extra overhead.<br /> <br /> AI<br />
i followed all the directions and everything but i am geting no charge out of the jack
if the orange light isn't lighting up on the PSP it probably is charging, but like he said, it is a bit under power.
yea i agree because i heard green leds take less power to light than other colors like orange wjite and blue
that really does not make any sense cause it probably has a circuit that lights a orange led when charging the battery. you need a certain voltage or it wont go. i learned this with a little thing i made up for this. it was a salvaged 4 battery pack. i just snipped a usb charger cord and soldered the wires on the pack. when the batteries started to die, they where putting out less voltage(what happends typically when aa's "die" ) they got below the 5V minimum and it stopped charging. i checked it with a multimeter too. btw, you really dont need to put any kind of resistor on the batteries because 6V isnt really going to hurt it that bad, if you need a longer charge, just go with c or d batteries(both 1.5 volts, just more power)
Yo same here but i used usb instaed of jack
me either...
Dude its not charging in the picture (the red indicator light on the PSP is not on).
if you read, he said it doesnt always register because it is a little below power. but also, if you look at the altoids tin its led is not on either.
I would really highly recommend a diode to be included. Although it isn't essential, inserting the batteries backwards CAN AND WILL destroy the 5 volt regulator. This design marks the battery connections pretty well, but I used a battery pack connected with 9v terminals on my PDA/PSP/USB charger and my friend hooked the connector up backwards and fried the whole device. My new version with a diode eliminates this problem. Putting the diode between the batteries and the regulator means that power only flows one direction, preventing backwards flow that could destroy it.
I just want to be safe when i finish mine up even tho this instructable doesnt work... the part w/o led and switch works... so what diode u reccomend .. plz post a link if u can ty
what diode do u recommend?
OKay. I made the charger diagram from the battery to the 5v reg to the usb ... that's the only parts that are recieving voltage from the batteries. idk what's wrong i have DPDT switch has 3 prongs and a led in a holder..... any ideas what im doing wrong plz reply
is there a way i can make sure my wires for the dc connector from the phone jack have juice to them?
could you get a closeup of the circuit i am having a hard time knowing what to do i did it the way the diagram shows i think but i don't get a charging light at all.
no charge in the psp. is it because the regulator that you posted gives out 5V and only 1000mA? didn;t it need 2000mA? just asking.
Umm... Actually it needs 500mA (max) so the reason it didn't charge is because your battery's toast.
I don't think that my battery wore bad, because they wore brand new, and i even recharged them. the reason that i said that it needs 2000mA is because of the original psp charger, witch puts out exactly 5v and 200mA.
I was talking about your PSP battery... Anyway i'm more used to MintyBoost style things now...
hmmm workin now. in the altoids. but it only pumps out 2.5 volts....mabye i could use a nine volt and some resistors.
9v batteries are horrible for charging USB-powered devices (or 5v at 500ma) because the internal resistance is so high. Therefore DON'T USE A RESISTOR!! (I'm not shouting, I'm typing in capitals.)
why do i need a 5v regulator? i got a store bought battery-charger and all it contains is a AAAx4 holder and some wires but no components or stuff !
Because 6v will fry the device. I bought a Belkin 6xAAA charger and it has a chip, regulator and resistor inside it... (and 2 wires and a female USB plug.)
Also... Why is the "positive" end of the battery pack going to the input on the regulator?
Because negative is ground?
Why do you need to have a DPDT switch
A toggle switch/rocket switch would be fine I guess...
I am currently building this project. All I have done so far is hook up the positive and the negative wires from the battery case to the regulator. I left the batteries in the case overnight and the regulator got really hot! Will this happen when I'm done and is it a fire hazard?
Im confused about this part The output plug and the LED are wired in parallel (if they are in series, the LED will suck up too much voltage, I learned that the hard way) through the switch and the regulator,
Hey My soldering iron sucks because the tip is broken so how can i solder small metal such as on the switch button etc.?
Hi Instead of using a phone jack ... Can i attach a female usb port ??? Would the wire from the switch go to the positive end of the usb port or negative end ...? Or the neg. wire to the switch with the positive end connecting to the other 3 wires...?
<strong>1. </strong>How long do the batteries last? <br/><strong>2.</strong> How many charges can it do, before having to replace them? <br/><strong>3.</strong> Can you get all the wiring and switches from Radioshack?<br/>
what happens if you leave it on overnight won't it overload the psp?
no it wont we charged a psp for a whole week in a rv no sign of overcharge ps that time is not exactly a weekend i was unplugging the rv from mains everyoften so they go out and play instead of playing call of duty on psp
i have a questions. i am a cheapo, and i "found" a few resistors, soddered them together and got 4 new duricell aa from 6.34 volts to 5.20 volts(or close) do you think i could use the resistors instead of the regulator. people are saying that you dont even need the regulator but i just want to be safe. so would that work? also, would the psp charge if the voltage was lower than 5v? and please answer.
<ul class="curly"><li>yes resistors will work</li><li>no it may not detect it</li></ul>
do you have to use speacker wire or can you use hookup wire
ya u can
Ok 2 Questions -1 can I do this with out the regulator or a regulator from a mother board -2 can I add a usb port and have the an outlet for the psp -2b if so can I run them both at the same time ?
-1: depends-it must be 7805 -2: yes -2b: yes but the batteries will discharge faster
yeah i want one
How come the LED is not on in that last photo. Is there a possibility that I could fry my PSP even if I do everything right. I dont want to take a chance just bought that new Silver 2000 version and saved for awhile. Looks awesome.
nah, you wont fry your psp, i have made one of these, and bought one, the one i bought though, was just 4 aaa's attached to a diode, then the plug going directly to the psp, the regulator is not needed, and draws valueable power. just glue everything down well, to insure nothing will short and you will be fine, even if it did short, the only thing to get hurt should be the batteries
Thanks, tyson. I have built it but went a little simpler with the 4 AA Energizer rechargable batteries. Thanks Jacob S. for putting it on here.
Okay, two ideas. 1. Maybe use two nine volts. I noticed the regulator could handle up to 35 volts, so 18 would be fine. 2. Why do you need the headphone plug and jack? Or is that just so you could have a detachable cord. If it is, good idea.
Nope. A 9V is a very poor battery for charging, they have a high internal resistance and lose a lot when you draw decent amount of current from it, as in battery charging. AA is the best bet here. Even better ..use RECHARGEABLES. They will supply a lot of current before the voltage drops too low to charge.

About This Instructable


58 favorites


More by Jacob S.: altoids PSP recharger
Add instructable to: