Install Sound Deadening Material in Your Car! (fake Dyna Mat) to Make Your Car Sterio Sound Awesome!





Introduction: Install Sound Deadening Material in Your Car! (fake Dyna Mat) to Make Your Car Sterio Sound Awesome!

ever see something that's all packaged nicely and sold for an exorbitant sum and think to yourself. "I could make that!" or "that's just _______ in a shiny package!" that's what I did one day when looking for sound deadening material for my car. Dyna mat is a really great product that really cuts down on road noise, body noise/reverb  from your awesome system and other annoying sounds in a car. The thing is that it's expensive! I realized that dyna mat is actually sold at Home Depot for a completely different purpose! it's used as a flashing material on house roofs!
the HomeDesperate sells the stuff for 20 bux a roll vs dyna mat's $100!

Step 1: First Step Peel It Off the Roll.

I'm a little slow sometimes so it took me a minute to figure out how to get it off the roll. Now is also the time to make sure your surface is clean!

Step 2: Cut the Piece to Size

I tried knives and my built-in bionic eye laser to cut the stuff but I found that a old pair of scissors worked the best to cut the junk. it's got tar on the back side of this stuff so the scissors may get a bit gummy by the end of this.

Step 3: Peel the Backing Off and Start Smoting It Down

I used this special roller thingie to press the stuff down into all the nooks and crannies. it worked good. I don't know where the roller thingie came from. maybe from a magic toolchest or something. in fact it may be the only one like it on earth... but it worked great.

Step 4: Do That All Over the Place.

it doesnt' have to look perfect cuz usually it's covered over by something. like.......

Step 5: ...CARPET!!!!

Now just to do the rest of the floor area, inside the doors and stuff....



    • Microcontroller Contest

      Microcontroller Contest
    • Science of Cooking

      Science of Cooking
    • Pocket-Sized Contest

      Pocket-Sized Contest

    We have a be nice policy.
    Please be positive and constructive.




    Just a heads up, but the roof repair tape is an asphalt product and dynamat is a rubber product. The net effect for sound deadening is not wildly different, its true, but the asphalt tape will off gas cancerous fumes. Not saying you shouldn't go for it, but recommending the asphalt tape as a direct replacement is not accurate or healthy.


    Thanks for the comment ManD4

    I Looked up the MSDS on AlumiBond, it has 0 VOC and:

    "solids formulation of synthetic resins, thermoplastics and non-curing rubber"

    it's available here:

    I prefer to use that brand as it's a little more rubbery

    The U-Seal featured in the picture has very similar properties.

    You can find the MSDS for U-Seal here if you're concerned. -

    Just for spits and googles, I googled the MSDS for Dynamat. this is what popped up:

    it seems to have the same active ingredients as the U-seal. (and other ingredients that pose potential (but unlikely) hazards

    An aside: From the factory the VW beetle came with asphalt sound deadening material allover the interior of the vehicle, we removed them in the restoration. There is no smell in the vehicle and it does not seem to move around in hot weather.

    Is it a direct replacement? no....ish

    for all intents and purposes, it's the same. I try to do the requisite research and I'm sorry I didn't lay it all out in my Instructable.

    Welcome to the community and I hope you'll share some of your projects with us as well!


    Right on, Josh. I apologize for assuming otherwise. There have been a lot of people passing off some nasty stuff as Sound matt lately, so please forgive my vigalence. Your due dilagence is refreshing. Thanks.

    Just the facts... Nicely done. I enjoy reading these comments sometimes just to look for the inevetible naysayer; warning of impending death and mayhem for those who follow the instructable. Rarely do thse folks include any facts... but rather just their opinion. You've done a nice job of answering the "concern."



    Dyna Mat is 1.7 mm thick. The product in the first link given is only 0.508 mm (20 mil) thick. How many layers would be needed for a competition mobile auto installation running 2K watts RMS into four 12" subs?

    How many of the 6''x25' rolls did you end up using?


    I think I used 2 for the entire car including the frunk

    Ice and water guard does the same exact thing and it comes in much wider sheets. I have used that in many a vehicle and it works great!


    I'll have to check that out! thanks!