Introduction: Knex Airsoft Bb Holder

Picture of Knex Airsoft Bb Holder

its light and compact holds around 16 bbs it has a latch that you twist to the side to let the bbs out

Step 1: The Pieces YOU Need =P

Picture of The Pieces YOU Need =P

1 red rod (2nd largest), 1 rubber band, 1 orange double sided connector,2 y shaped lego hand look alike pieces, 15 purple 1 part one hole connector, 1 1part connector no hole. I tried to describe the best that i could

Step 2: Step 1

Picture of Step 1

attach one of the y pieces to one of the sides (its best if u do it like the pic)

Step 3: Step 2

Picture of Step 2

then slide the orange piece through the hole on the rod this will be the mechanism that will let the bbs out when u turn it to the side. (the orange piece is next to the y piece)

Step 4: Step 3

Picture of Step 3

now attach all 15 one connection pieces to the rod. (opposite way of the first y piece, next to the orange piece) as shown in the picture

Step 5: Step 4

Picture of Step 4

now attach the other y shaped piece to the no hole one connection piece. as shown it the picture. this will stop the bbs from coming out of the back of the holder.

Step 6: Step 5

Picture of Step 5

attach the piece u made in step 4 to the end of the holder next to the 15 connectors as shown. make sure this piece covers the hole of the connector at the end so it will block the bbs from coming out. and make sure its opposite from the y piece at the other end.

Step 7: Attaching the Rubberband

Picture of Attaching the Rubberband

all you have to do is take the rubberband and put it around the holder make sur that it is closest to the rod as you can get it as shown

Step 8: How Do I Load It?

Picture of How Do I Load It?

easy,trn the orange piece and drop the bbs in,then when u let go of the orange piece it should go back into place and the bbs should not fall out. this is my first instructable, so i hope this will be useful if u have questions plz comment

Comments

Burnsides (author)2011-06-24

I think with a bit of tinkering, this could be made into a speed loader! Thanks for the basis man!

By the way, great job for your first instructable! Keep it up!

Raiden97 (author)2009-08-03

this is somewhat useful to me...my m16 clip holds 16 bbs, i have 3 clips, and a speed loader.

airsoftplaya (author)2009-05-29

well if u noticed its not supposed to be a speed loader

okoshima (author)2009-05-28

16 bbs... that will save you... /sarcasm

lets be honest here, its not a speedloader or even a loading tube, it holds bbs.. usefulness = 0 being as you can use... the bag the bb's come in, or the tub/tube (apparent quickloader but we all know they just jam) or even a empty plastic bottle.

all hole a lot more bbs and need less work. if you cant fit one of these in your pockets... get bigger pockets.

Killer~SafeCracker (author)2009-05-28

This Is pretty good. 4.5 and faved

airsoftplaya (author)2009-05-28

i know its not he greatest but it was pretty useful when i used it

jakee117 (author)2009-05-28

honestly, just buy a speedloader, they are like, 7 bucks, and If this gets shot, you get plastic in your face. sources- 4 years of airsoft experience ARMOURY e1 g36c kjw m1911 tactical utg tri shot shotty soon gettting either an echo 1 or mauri mp5k

pls (author)2009-05-28

I know a good idea! A pocket! :)

TwistedParadox (author)2009-05-28

I made something like this to hold blue rods

About This Instructable

1,827views

3favorites

License:

Add instructable to: