Picture of Nerf Mavric super powerd
This is instructabule is for the Nerf  mavric, it increases loading speed and power. and a dart mod

I am not responsibly for any or a injure, or involvement with the law on your part, so think safety! Be sure to where proper protection and be sure to secure all protection
Remove these adsRemove these ads by Signing Up

Step 1: Tools and supplies

Picture of Tools and supplies


screw driver


Nerf mavric
Nerf whistle darts
air soft BB's

Step 2: More power!

Picture of More power!

This step will show your how to super power the Nerf gun.

First. open up the case, by unscrewing with the screw driver.

Second. detach the top piston spring, then take out the second 1"in spring and place inside the larger spring, make sure it only sticks about one fourth the way, when lined up with other spring, if not use the wire cutters to cut the right about off.

Third. Take the wrench, clamp the spring and push the way that the spring goes until it gits large enough to fit the spring couple.

Fourth. shove the spring back in place and make sure it fits and will lock in place when cocked.

Step 3: Restrictions!

Picture of Restrictions!
unfortunately every Nerf gun has restrictions, however, you can take them off, by following this step

First. open up the chamber that holds the Nerf darts, and carefully pry it open with a screw driver and watch all the little wimpy springs and forks fall out, once they are all gone just put the end back on the chamber.

Step 4: WARNING!

Picture of WARNING!
Somewhere in this mix of moding your Nerf gun, you may have lost a little spring that goes to the trigger,this can be replaced my cracking open a mechanical pencil or pen and sizing the spring to fit the triggers couple.  AND WORKS BETTER THAN ORIGNAL

Step 5: Air soft dart mod

Picture of Air soft dart mod
This step will show you how to mod a Nerf dart to perfection,

First. get 1-4 air soft BB's and slide them in to the small hole in the tip of the whistle dart. and walla!
The dart now is vary hard, and painfull

The second mod!

Take a air soft BB and place it in the hole in the END of the dart and it will now launch when fired

Step 6: PAINT

Picture of PAINT
I painted it
1-40 of 82Next »
jumpingcat4 years ago
hey guys check it out
mods i did
-cpvc barrels
-ARR (air restrictor removal)
-penny mod
-put bolt in slide(it broke before:(
-all of the steps above


codymen4 years ago
cool i'll try it
rapid nerf monkey your gun may look awesome but the end of the barrel is painted too, you need to have it orange so the cops no that it is a fake gun and not real so i would start un-painting the tip of the barrel.
ya i figured that out. mine is screwed now, so i'm using the spring for something else.
HighWing4 years ago
In my experiences, removing those actually reduces the range a dart will fly! I am fairly certain those are actually put in to prevent large air blasts during a dry fire. The only thing that will actually increase the range of the dart is replacing the air compressor spring.
very, very wrong
inergy HighWing4 years ago
pandabird134 years ago
Would the dart mod work with the clip system darts?
knuckel (author) 4 years ago
More of my youtube :D http://www.youtube.com/user/SliceAndDiceStudio?feature=mhee
 im having a hell of a time getting the nub off too..  pushing isnt helping, tried for half an hour... any other suggestions?
me to but i dont see any silver peg on the back. could you add a pic?
knuckel (author)  cmccarty07245 years ago
 also, it has been a while since i have done this, but look for a silver peg sticking out of the back and press on it realy hard and twist and it should come right off
knuckel (author)  cmccarty07245 years ago
 trust me try relay hard, it is tough, make sure u have all of the skews un done, if necessary you may need to resort to pliers of a large size 
cookie384 years ago
I need a good mod that i can use and whoop my little bro w/ my mav and nite finder
lil larry4 years ago
TIP: for the wistler darts rip the wistle off. This realy helps.
Furloy4 years ago
skrew this just make stefans
Furloy4 years ago
you need 2 cut the long things off and sand it down
knuckel (author)  Furloy4 years ago
i will try that next time i update this
corn holio4 years ago
one heluva bad assed nerf gun
Tadashi984 years ago

awsome gme
d-rider4 years ago
the syrup made my gun jam thnks alot!!!!!!!!!!!!
It was your fault seeing that you chose to mod so, thats not his fault.
knuckel (author)  Doctor Freeman4 years ago
rofl :D do u like waffles ya we like waffles , do u like pancakes ?, ya we like pancakes ,do u like French toast, ya we like French toast !

Do you like waffle? No, I like pancake.
i followed the directions exactly and all it does is make a big loud noise!?!? : (
knuckel (author)  the all powerful cow4 years ago
ok, i have yet to still Finnish this instructable, insted of using two springs extend the spring that was original in the gun. if the coking mec breaks, cut off the top slot for it and use a skrew driver, trust me.
ggg36364 years ago
NICE!!!!! but why is the top all black and not white
knuckel (author)  ggg36364 years ago
i wanted it to look more real like, but to have a aged appearence
[corosive]4 years ago
sick man. i love it.the link here told me how to paint mine.camohttp://www.youtube.com/watch?v=6q6D7Njvedo the only problem is that when the slide is being cocked, it tends to grind the paint and take a while. my camo gun pics included.
knuckel (author)  [corosive]4 years ago
nice paint job! 5 *, and thanks for the support.
ubcrazy25 years ago
beast paint job. i made a wicked paint job to 2 nerf nite finders
CaseBoy5 years ago
this link help me a lot... http://www.youtube.com/watch?v=egin2_oTs0w
FFVIIBOY5 years ago
i think this is my favorite Nerf gun, it just seems so cool to me,  i dont have it but ive used it, and i want one
knuckel (author)  FFVIIBOY5 years ago
wow, i feel so speshal now ^.^
actually i was talking about the kind of Nerf gun maverick but this tutorial is also cool
cee41 knuckel5 years ago
but, where can i find a spring, and plus when i tried the air restrictor removal, the gun broke. DX
knuckel (author)  cee415 years ago
 oh now, rofl 
 I found if you take a pair of decent sized wire cutters and slide them under the front grey piece on the orange end of the barrel and squeeze it comes right apart no problem
knuckel (author)  GreatClownKing5 years ago
jcksparr0w5 years ago
i think its kind of illegal to paint the tip of the barrel
1-40 of 82Next »