Introduction: New and Improved Altoids Blowgun

i have improved the original one into a pimpin' one

Step 1: Gather the Supplies

now u will need 7(ish) supplies
~altoid smalls
~an emty pen or, for u over-acheivers, an airsoft gun barrel
~a hot glue gun
~electrical tape
~airsoft pellets
~aluminum foil
~wire cutters
(ish)

Step 2: Cut Notches for Barrel

now we must cut the notches for the barrel. we must do so with
wire cutters.
we must also cut another notch in the lid o the tin

Step 3: Glue It BABE--------O

glue the barrel to the tin. strengthen the connection w/ the E-tape

Step 4: Finish It Up

fil it with ammo and slip the cap on.

shoot the heck out of the guy at walmart!


This is reece. i shot him with my altoids blowgun.
............................................................................................................................................................his grave reads..............................
............................................................................................R. I. P.
Reece, killed by
mint kandy and his friend.

Comments

author
adamthiede made it!(author)2007-07-22

how does the ammo get into the barrel? it just looks like its sitting there.

author
joemonkey made it!(author)2007-07-24

u put it in the barrel. i was making an auto feed, but its not #1 on my list.

author
pengyduck made it!(author)2007-11-16

maybe make a hole in the side of the barrel inside so the bullets will fall in when you turn it sideways, it's a start

author
tanmanknex made it!(author)2009-07-18

and then put a tiny peice of paper in as a stopper

author
Cubie2 made it!(author)2011-03-21

I KNOW WHERE YOU LIVE TANMAN!!! WHAT NOW?!?!?!?!?!?!!!

author
tanmanknex made it!(author)2011-03-21

Well, judging by the fighter jet profile pic, name of Cubie, and the fact that you obviously know where I live, I know where you live too!

author
Cubie2 made it!(author)2011-04-01

*GASP* Oh dear...

author
Cubie2 made it!(author)2011-03-21

Ok, so what you do is you put a pin inside the pen casing with the tip poking through a thin water balloon. Then you put the tip on over the water balloon and add a tail to the dart a wala! You have an extremely powerful blow dart gun. I'm working on putting a compressor in so that it gains the air it needs itself.

author
benduy made it!(author)2010-11-13

Whats with the fat guy

author
popcorn4lunch made it!(author)2011-02-16

thats what i was wondering....

author
Spl1nt3rC3ll made it!(author)2007-04-25

Man I hate that Walmart guy. He's always giving me that "I know were you live" look. Mabey its because im his neighbor... anyway, REVENGE!!!. I can't wait to annoy him all day and then get tackled by security when they figure it our. :)

author
Doctor+Freeman made it!(author)2010-09-09

you know those benches by the greeter and when he looks the other way (this reminds me of this walmart guy he never looks up at the time my sister being only ohh idk.... 18 lol she stood in his line of vision and all he said was hello goodbye hello goodbye hello goodbye ect. untill my mom pulled her away and said stop it) (shoot) huh? (shoot) huh? or when people flip you off in wall-mart mam could you please look this way i'd like to give you something WHAT? (you friends shoot) (ALTOIDS say burp) lol ow what the (your friends shoot) (altoids say burp accaully you should put a recorder of that thing on amarican dad of spider say burp but only slice it and take sounds and put them in so it says altoids say burp)

author
spikelea made it!(author)2009-07-08

I made it and #1- it works amazingly well/ the bullet goes nearly 20 feet. #2- it holds roughly 80-100 bb's #3- if you put a thread stretching across the opening of the end you blow on, it will allow you to load it through the other side and it wont roll out

author
miqt made it!(author)2008-04-05

haha i used to make stuff like this and use it at school, except i would just use the tube on pens, it works almost just as well.....depending on the pen.

author
andrewdpham3 made it!(author)2009-02-03

I make bow and arrows out of pens and rubber bands. really simple but only one peice of ammo. any suggestions?

author
PKTraceur made it!(author)2008-08-20

I used a gel pen tube and the tube is like (the bottom,) so the bb stops halfway. |||| |||| |||||||| ||||||| ||||||||||| ||||||||||| |||||||||||||||| |||||||||||||||| |||||||||||||||||||||||||||||||||||||||||| |||||||||||||||||||||||||||||||||||||||||| |||||||||||||||| |||||||||||||||| ||||||||||| ||||||||||| |||||||| |||||||

author
smboling made it!(author)2008-06-01

My Altoids tin disguised it the whole time.

author
smboling made it!(author)2008-06-01

Yeah, I used a pen tube and airsoft BB's and I hit my teacher on our Field trip, She never found out it was me.

author
theosullis made it!(author)2008-03-10

The barrel is very small i would not think it the bb would go very far.

author
bowow0807 made it!(author)2008-03-01

cooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooool!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

author
jeffconnelly made it!(author)2007-11-18

Do you think that it would work in other containers? maybe you could have a tic tac container with the tube on one side, and the ammo stored so you get it out like a tic tac?

author
PyromaniacDaniel made it!(author)2007-10-17

add a paper towel to line the altoid can to keep the pellets from clanging

author
joemonkey made it!(author)2007-07-02

omigosh i completely forgot about that! i did get part of thi idea from u, but most of it was me and my friend trying yo conceal a gun

author
Mace42 made it!(author)2007-06-09

Dude is that you? Why the squint lol~

author
joemonkey made it!(author)2007-06-09

oh him? haha no, that is m' good friend reece! he is squinting from the super bright flash on my camera(i hacked it) and cuz i shot him in the ear with that gun! TEE HEE!!!

author
Mace42 made it!(author)2007-06-09

..teehee!!

author
Opieone made it!(author)2007-06-01

What i did was take the pen shell thing and taped to the bottom of the altoids case then drilled a hole through the bottom of the altoid case and into the pen so it has auto feed

author
icedog515 made it!(author)2007-04-25

wait...i dont get it. do you blow through it or sumthin??im confuzzled

author
casvandegoor made it!(author)2007-03-02

nice idea! (also watch my guns!)

author
Squire_Bullet made it!(author)2007-02-25

Well how about something more Practical, what about Gander Mountain?

author
joemonkey made it!(author)2007-02-26

well i gess if they carry them?

author
Squire_Bullet made it!(author)2007-02-14

where do you buy airsoft Barrels?

author
joemonkey made it!(author)2007-02-14

well one way is buy a peice-o-crap gun and tear it up you also could look online for a parts website

author
Jack+Daniels made it!(author)2007-02-10

you should build a hopper into it thats also pressurised by your breath so you can fire more than one at a time

author
joemonkey made it!(author)2007-02-11

thanks for the suggestion. i would have, but this was a plan for a concealed blowgun. i'll make some thing later and post it.

author
bigpinecone made it!(author)2007-02-10

hmmm, i'm bored and i'm using my mp3, i'll go build a breech version yay

author
bigpinecone made it!(author)2007-02-10

heh, took me all of 15-20 mins to build

author
bigpinecone made it!(author)2007-02-10

WOOT i'm done with the instructable, it has a vid too

About This Instructable

17,258views

49favorites

License:

More by joemonkey:Puppy-Exersize Mobile!knex stiletto grill ignitor mini-taser
Add instructable to: