inspired by a combination of throwies,'s "annoy-a-tron" and my recently discovered love for 555 timers, I've come up with this little guy. i call it the "timed soundie"

once the switch is flipped on the timed soundie, you have 12 seconds before it emits a nice loud and constant beeeeeeeeeeep, enough for me to hear throughout my whole house. on the underside of the soundie is a magnet, becuase throwing them to places people can't reach is fun!

this instructable inspired in part by:
buzzer throwie
the original LED throwie
Remove these adsRemove these ads by Signing Up

Step 1: The nitty-gritty...

Picture of the nitty-gritty...
parts list:
10uF capacitor
2 3v button cells (cr2032)
1 M ohm resistor
piezo buzzer (about the width around of a 3v button battery)
555 timer
electrical tape

(this is my first time drawing a schematic, so tell me if its wrong!)

the legs of the 555 are bent out and the whole circuit wraps around the buzzer.

all of the parts are soldered or taped directly onto the 555 or the piezo buzzer. the wires soldered onto the circuit going to the batterys are just taped to the top and bottom of a stack of two button cell batterys. like a soundie sandwich, a battery is added and taped to the bottom. (this is optional, incase its just being used as a sound grenade to bother people or for use in an airsoft or paintball scrim)

NOTE: the buzzer's + should be connected to pin 3. the - is connected to pin 1.

Step 2: Throw it!

Picture of throw it!
i've found these little guys do a suprisingly good job at sticking to things. you obviously can't chuck them like you would a throwie, but a nice loft will generally land you a stick. just be sure to flip the switch before you toss it ;-)

(if just being used as a sound grenade, be sure to pad the little guy; he's probably fragile!)

thanks for visiting my first instructable, and please visit my website:
1-40 of 78Next »
lxavier22 months ago

I have a question I'm new to electronics but would like to know what capacitor is it all I can find is 10uf can you please tell me :) :) :D

icewolf4 years ago
 Mod this thing to fit a 9v battery, then throw it behind a big heavy closet.
Now wait for it to discharge completely !!!

Nice instructable!
icewolf icewolf4 years ago
 or add a CDS cell so everytime someone looks for it with a flashlight , it stops working  LOL
pokemech icewolf8 months ago
Easy there Satan...
techno guy2 years ago
is there an equation that can give the values of the capacitor and resistor for a given amount of delay, or visa versa
biboNL4 years ago
ok, so my nearby DIY store sells either 4.7 Mohm or 240 Kohm resistors, and no 1Mohm resistors.
should i just slap a few 240 Kohm resitors behind eachother or should i go for a 4.7Mohm resistor?
go for the 4.7 MOhms 5min get a way time LOL :)
Johnny C.4 years ago
I build one too!
But mine starts after 8 secs!
use a bigger resistor like 1.3MOhms :)
And i made a new schematic. Here are the positive and negative parts marked!

techno guy3 years ago
Mine doesnt work. It only works when you disconnect the wire from the piezo and reconnect it.
when you reconnect it does it go the whole way of just when your reconnecting it try putting a resistor in front and behind the pizzo
PhilipK733 years ago
This is a great guide and my first look into 555 timers (and electronics in general). I have a question though, how would you make it go off in 3~ seconds and then turn off after buzzing for 5~ seconds? I plan on using this for a "sound grenade" and use the IntrudAlert Alarm ($1 at local store).

To make it go off quicker, I would assume you would use a smaller capacitor (maybe 5uF?) but how would you make it stop?
jhakker3 years ago
Anybody know of a good website to buy these parts cheap
tesla coil5 years ago
Could you use a 1K Resistor ??
let_it_out_org (author)  tesla coil5 years ago
no, not enough resistance. maybe with a bigger capacitor, but a 1K resistor would make the 555's output go to high immediately
what if you use 720M farads? lol an hour timer? :P
No such thing as a MFarad, plus a farad alone is huge, VERY huge
a_d777 doom86663 years ago
Its so huge, you can run this circuit for about 20 minutes on it!!
also i mean Mega, unless u meant micro with that m
 indeed meant micro :)
(removed by author or community request)
Actually it's µ.
I will have to try that.
sci4me4 years ago
would an electrolitic capacitor work???
cdousley4 years ago
how long do you think this battery will last?
 wats that thing that says lioorg?
 an add for his site...
Articas4 years ago
could you attach the flash circut fron a camera to make a timed flash grenade
matstermind4 years ago
my timer just heats up
check your wiring you might have created a short some where. also check to make sure u didn't hook it up backwards since the diagram on here doesn't have polarity symbols on the battery
bigstiffy4 years ago
How do you have the button cells hooked up?
geeklord5 years ago
WOO!, first to comment! Awesome, might have to try this on an Algebra teacher >:-)
Noone likes someone who is happy to be the first one to comment.
revhead5 years ago
i made this exactly as outlined by the schematic and it didnt work, why? are the pins 4,5,7 not used, or do they go to ground? any help would be great, cheers!!
4 is for RESET, which means that it will reset the circuit when voltage is applied. Here, you time it only ONCE, the "12 seconds"
let_it_out_org (author)  revhead5 years ago
4, 5, and 7 should not be connected to anything. be sure you're using a buzer and not a piezo element. if you apply voltage to your piezo (touch both contacts to a button cell) it will beep. it should have a + and -...something i guess i forgot to mention is that the + should be connected to the 3rd pin.
I think i bought a piezo element, how do i use that in circuits?
Piezo element u need to hook it up to a timer, which is the job of the 555. So really, forget about making something from a piezo u could make a REALLY REALLY annoying thing though from it.
thanks. the problem that I am having is that as soon as I connect my power supply to the circuit, there is no delay in the buzzer sounding. it just starts to beep as soon as the power is put to the circuit. could this be a problem with the capacitor. the capacitor that I am using is a 10uF 35V tantalum capacitor. i am also using a 1M Ohm resistor like you suggested. Thanks for helping me out. Cheers.
1-40 of 78Next »