Tell us about yourself!

Complete Your Profile
  • AyushP2 commented on gigafide's instructable Control A Computer With Your Mind!9 months ago
    Control A Computer With Your Mind!

    it is actually possible to use the arduino uno to move a mouse WITHOUT using dfu and uploading a hex file. I did it by making some arduino code and java processing code and it worked, if you would like to know how, comment back,

    View Instructable »
  • AyushP2 commented on AlmusYang's instructable Building a 3D Printer Under 200$10 months ago
    Building a 3D Printer Under 200$

    USD

    I believe it is possible, but that would be whole new sizes of parts. However, the only mod I have done is a heated bed on this.

    View Instructable »
  • AyushP2 commented on arpruss's instructable Mindflex EEG with raw data over Bluetooth10 months ago
    Mindflex EEG with raw data over Bluetooth

    I decided to strip off the Bluetooth of off the headset and desoldered all the wires and I tested the headset with the board game, the board game received no signal. I don't know what happened to the headset, but I believe that is the problem, it doesn't send a signal at all.

    I believe this was due to me placing helping soldering hands on a pretty bad place that has circuitry.

    I tested my device with a bluetooth, new module this time and it doesn't work with any device, why is this problem persisting, before modding, the headset worked with its board game.

    View Instructable »
  • Adding Bluetooth to an EEG headset for mind-controlled projects

    My headset works wit no device, plz help.

    View Instructable »
  • AyushP2 commented on arpruss's instructable Mindflex EEG with raw data over Bluetooth11 months ago
    Mindflex EEG with raw data over Bluetooth

    I'm afraid not but why, is it to check even if it does send sounds?

    But the Mindflex works, I tried it with the board game

    thanks so much for replying, my problem is I'm using Trent Brook's BrainWave and when I connect it to my Bluetooth using the mind flex, it connects but transfers no packets and after a minute or so it disconnects, and yes the lights are solid during connection so I was wondering if the mode was the problem or power. Thank you so much for your help.

    I connected R to TXD, but it still refuses to connect to anything. I am very confused.

    View Instructable »
  • AyushP2 commented on arpruss's instructable Mindflex EEG with raw data over Bluetooth11 months ago
    Mindflex EEG with raw data over Bluetooth

    My headset doesn't respond to graphs, is it because I have not connected R to TXD on the HC-06?

    View Instructable »
  • Adding Bluetooth to an EEG headset for mind-controlled projects

    Why would you have to disconnect the + pin from the EEG headset, that makes no sense

    View Instructable »
  • Adding Bluetooth to an EEG headset for mind-controlled projects

    Hello, I am having problems with the HC-06 module. It keeps reconnecting and disconnecting from my mac and PC. I have tested the voltage on the multimeter and it stays stagnant at 3.35V. Is this the problem, or is it something else.

    More info: Inside the headset, if I measure the voltage it reads 3.24V, is power the problem?

    Hello, I am having problems with the HC-06 module. It keeps reconnecting and disconnecting from my mac and PC. I have tested the voltage on the multimeter and it stays stagnant at 3.35V. Is this the problem, or is it something else.

    View Instructable »
  • AyushP2 followed 3D Printing channel 1 year ago
  • AyushP2 commented on AlmusYang's instructable Building a 3D Printer Under 200$1 year ago
    Building a 3D Printer Under 200$

    This a house I had made and I have plans for other prints, and your firmware is accurate for me, just needed to change VREF

    It was some Lubricant that accidentally got on the wood. The lubricant was meant for y axis

    Here is a model house I printed, and thennI will print a mental toy for doges and then some prostehetics

    The wet thing is Lubricant meant for Y axis but got onto the frame

    View Instructable »
  • AyushP2 commented on AlmusYang's instructable Building a 3D Printer Under 200$1 year ago
    Building a 3D Printer Under 200$

    Thanks so much guys for helping me along the way. If it weren't for you guys, I couldn't make this. Thanks to you, I've won 1st place at my district tech fair. And I did give credit to AlmusYang during the fair.

    View Instructable »
  • AyushP2 followed appleman1239871 year ago
  • AyushP2 commented on appleman123987's instructable Edge 3D 3.0 - A $200 3D Printer1 year ago
    Edge 3D 3.0 - A $200 3D Printer

    This is a very simple design, kind of reminds of a Prusa i3 for some reason. However, what bothers me is the 3D printed parts. I am a 13 year old maker and I had recently built a 3D printer under $200 only using Laser cut parts in the design similar to a Printerbot. It's really cool how you made this, and if you ever need any help, just shoot me a message through instructables

    View Instructable »
  • AyushP2 commented on AlmusYang's instructable Building a 3D Printer Under 200$1 year ago
    Building a 3D Printer Under 200$

    My Y axis I was noticing is a little slanted. Is this for everyone or is just me because I used wood as the bearing instead of acrylic.

    View Instructable »
  • AyushP2 commented on AlmusYang's instructable Building a 3D Printer Under 200$1 year ago
    Building a 3D Printer Under 200$

    And my controls for pronterface are correct

    And I noticed that you didn't put Machine (0,0) as a machine setting, when I uncheck this, the Y axis goes all the up and unlevels the bed, and sometimes goes off the bed. So isn't this a problem?

    My axises are correct the way you describe them and I use Pronterface

    As a matter of Fact, I selected reprap when doing machine section and then other

    View Instructable »
  • AyushP2 commented on AlmusYang's instructable Building a 3D Printer Under 200$1 year ago
    Building a 3D Printer Under 200$

    The link returns a 404, and here is what it thinks is a circle.

    The link returns a 404, and here is what it thinks is a circle.

    Yes U dud

    The link returns a 404, and here is what it thinks is a circle.

    View Instructable »
  • AyushP2 commented on AlmusYang's instructable Building a 3D Printer Under 200$1 year ago
    Building a 3D Printer Under 200$

    I have a major problem. My printer isn't printing circles AT ALL. When I run the gcode, it chooses not to print a circle correctly and prints it as another shape I printed last week and assumes it's a circle. Is this a problem with Cura or Marlin. Please help and thank you in advance.

    The Breakout board may be loose, same thing happened to me, just had to push the board in more and it worked fine for me

    View Instructable »
  • AyushP2 commented on AlmusYang's instructable Building a 3D Printer Under 200$1 year ago
    Building a 3D Printer Under 200$

    I would like to highlight my issue, my printer isn't printing ROUND objects, but square objects are fine, how do I fix this

    I would like to highlight my issue, my printer isn't printing ROUND objects, but square objects are fine, how do I fix this

    My belts aren't loose. The problem is that the gcodes chooses not to print a circle correctly and prints it as another shape I printed last week and assumes it's a circle. Is this a problem with Cura or Marlin. Please help and thank you in advance

    View Instructable »
  • AyushP2 commented on AlmusYang's instructable Building a 3D Printer Under 200$1 year ago
    Building a 3D Printer Under 200$

    Hey, did you have any problem of Cura printing something else instead of the file, if so, can you tell me what to do to fix that problem.

    I would like to highlight my issue, my printer isn't printing ROUND objects, but square objects are fine, how do I fix this

    Make sure you've installed all of the jumpers beneath the polulu drivers

    Hey, did you have any problem of Cura printing something else instead of the file, if so, can you tell me what to do to fix that problem.

    View Instructable »
  • AyushP2 commented on AlmusYang's instructable Building a 3D Printer Under 200$1 year ago
    Building a 3D Printer Under 200$

    Do you think you give us your Cura profile, I really need help

    View Instructable »