3 Simple Ways to Share What You Make
With Instructables you can share what you make with the world and tap into an ever-growing community of creative experts.
Create on the go:
With Instructables you can share what you make with the world and tap into an ever-growing community of creative experts.
PDF Downloads
As a Pro member, you will gain access to download any Instructable in the PDF format.
You also have the ability to customize your PDF download.
Apr 16, 2009
81,836
%100%
%0%
Visit Our Store »
Go Pro Today »
Comment: Yes, it's a pretty cool platform for doing just about anything once a fart is picked up.
Comment: Yes it was, the gas sensor will only change the channel if it smells a real fart.
Comment: Holy cow, that's some dedication you have there! What can I say? I'm hot for teacher!…
Comment: Another nice write up. Is there a video of what the pedal sounds like? Fuzz comes in …
Comment: If I was better as sewing he would have! He sleeps with a framed picture of Lincoln ne…
Comment: It's just a toy. You put phrases onto an SD card into preset categories and it'll rand…
Comment: Yes it does. There's a short 7 second video on the intro of it working.
Comment: Yes, please keep me (us) posted. I'm interested to see how it turns out. Also, thank …
Comment: So you can't highlight the pulses in the serial monitor window? Are you using the vers…
Comment: It's not really strong by itself. It's the prep work that makes concrete strong, prest…
Comment: Well intentioned, but this makes me cringe a little. Concrete itself doesn't have a ve…
Comment: http://discgolfreview.com/resources/articles.shtml http://www.discgolfreview.com/forums/
Comment: http://www.discgolfunited.com/disc-golf-courses/ DGU is another good source or findi…
Comment: I don't screen print, but I do dye disc golf discs, which is similar.Suggestion: Have …
Comment: So I did a little Googling... seems Mighty Mite necks come pretty rough and need to hav…
Comment: No, the only guitar I ever put together was a Warmoth body and neck, but I can attest t…
Comment: Nice build and nice guitar! It might cost a little bit more, but if people are looking…
Comment: Yes, within a limit. There's a one minute debounce for the fart to clear out. So, as …
Comment: You could do that. I'm assuming a more intense fart would linger longer, so I'd start …
Comment: I've tried but there's a couple problems. There's a lot going on in a one second span.…
Comment: I actually did make it so it only changes the TV to real channels that work. To alter …
Comment: I actually thought about doing that. I'd need an EthernetShield and a couple XBees to p…
Comment: It depends on how big your battery is. 9v will spin faster than 3v (two AAs), will spi…
Comment: Very nice 'Ible and I feel your pain about snapping those little boards in half, done i…
Comment: Might be a silly question... I'm no gardener, this is for my Mama. Do the holes or the…
Comment: Maybe a silly question but, why is it a stereo input jack instead of a mono jack? Thou…
Comment: This should be in 1,000 point font and bolded! I ran into the same problem at first too.
Comment: Never mind, I figured it out. In case this happens to somebody else; my servo had a li…
Comment: I built one and tested it in it's box, but when it comes back to hit the microswitch an…
Comment: The temperature tolerance of MOST caps are fairly high, but it does vary from unit to u…
Comment: I'm sure you're safe when you do this, but I'd still like to put up a warning when heat…
Comment: Yes, a 2.2K resistor is what I used and it worked fine.
Comment: Starting from D4's anode (side without the black line) of D4 your circuit should look l…
Comment: Yup, same company and same prices. It's just a little trick to order from who has it i…
Comment: Guitar Center has owned Musician's Friend since 2000... check out, "Guitar Center," on…
Comment: The LEDs (I think, don't hold me to this) act as a low efficiency signal impeder. I do…
Comment: djajasoekarta: Yes, remove D5 and replace it with a 3mm LED and leave D4 alone for the…
Comment: I noticed when you soldered the 47pf cap across D4 and D5 the negative pin of D5 was sh…
Comment: What purpose does the nickel with a hole in it serve? I accidentally forgot to drill t…