With Instructables you can share what you make with the world, and tap into an ever-growing community of creative experts.
Tell us about yourself!
Hi, thanks for the info reported, the source code was shared directly from the developer, I have no idea how to use it, let me know what are you going to do with the source code.By the way, we found that Arduino can now support the stm32f103 MCU in this led cube, it means we can put some arduino code into the board and control the leds, we just finished testing with some sensor function, not yet start to control the led cube.
Hi, how long it takes to receive and display the GPS data? I have some cheap GPS, but the seller said you need to take outdoor for GPS signal...
Info for the IN-14 NiCiClockView Instructable »
Yes, we have IN-14 nixie clock in store, but shipping time is very long.The PCB temp affect the temp sensor, may need to place it out side the clock with cables.The dot inside the tube can only turn off by removing the pin connect to that dot, we don't have a solution to control that dot, tried controlling with different program and circuit but not work.
Hi, the schematic is not allowed to share by the developer. We will try to produce the clock as assembled.
Hi, other than add many hardware to the cube, you can also try IR sensor on the power plug, so it can power many electronic when you go in to the room, and place the sensor on top of the room.
http://www.ebay.com/itm/Outdoor-12M-Security-Infra... Infrared PIR Motion Sensor Detector
Hi, thanks for the question, info are added to the instruction, not extra item if you finished the assembly, all parts come with the kit.
Hi, can you contact me again in ebay? I lost your message, can't follow up you ID to resend the parts
pls contact me again on ebay, I will get it solved quickly.
Hi, please take a multimeter to check the 2 pins of that tubes not light up, check their voltage.And if you remove try either one 595 or the 2803 IC, the VFD tube should all light up, than the tubes are good working.
Hi, there are there 4007 diode in the PCB, can you double check if the direction and value mark are correct.
You need to do a solder check, if any solder shorted, than check if any IC behind the VFD tube reversed or not plug in correctly. else we will give you guide on checking the power circuit.
That can be the tube problem, remove one slight orange cathode tube, and there should have 4 working tube, and 2 not working, because each 2 tube are linked. If the leds are working and remote control are working you only need to replace that tube or 2 tubes.
most important is D1 in the middle of the PCB, D1 is a 4007 diode also
Hi, every IV-11 tubes has connected to the resistors and ICs just behind them, not sure if the ICs plug in correctly, should we resend the ICs or Tubes, that need your help to check or reinstall that part, and we got the right solution. If you are in a hurry, contact us in ebay and will resend both the ICs and tubes for replacement. We really need to know the cause so we can help other customer too.
Hi, he fourth tube can show a number 8 can be problem from the IC connect dock, if not we will resend a new tube to you.The full stops can only disable by removing the pin on the tube.PP and -- stand for nothing, just let you determine which is alarm and temp mode.
HI, it is not open source project, but a hardware kit for DIY, seems impossible to work with Arduino.
It will be ship on 25/11/2016, if you order now it will be ship on 25/11/2016 also.
HI, there will be YYMMDD DDMMYY MMDDYY 12/24hr Celsius/Fahrenheit in early December, currently only have YYMMDD MMDDYY Celsius/Fahrenheit option in the clock.
They will be shipped now, firmware arn't able to update, the developer don't want to share the firmware because of copy risk. And there are only 24hr ddmmyy degree C'。If big problem need to update the firmware, we will try just send the MCU to you.
Hi, it was fixed in the firmware code can't change it yet, only if new firmware can change it, but you will need a USB to TTL usb programmer to send the firmware.
AuraCube 8x8x8 Compelete As...View Instructable »
A new driver for the AuraCube444 is uploadedhttps://drive.google.com/open?id=0B3w2uIW46VgQQXZxQ2VnaldsclU
IV-11 VFD Tube Clock Assemb...View Instructable »
If I sell it on 19USD people are not care about money but the qualityIf I sell it on 39USD people are care both the money and quality, so they will like to solve the problem and discuss the issue.
https://drive.google.com/open?id=0B3w2uIW46VgQflFC...https://drive.google.com/open?id=0B3w2uIW46VgQLVpM...Hi these are the two folder
Hi, if any problem with the animation software you can contact me to solve it, it should be easy to work out.
It only work with the program and the hardware in that cube.
How is the remote control working? All mode should work if there is animation when powered.
Hi, did you connect it with a usb to ttl programmer?
Arduino Powered Sunrise Alarm Clock With Neopixels
Delta Bot: DIY 3D Printer
Hi, just started to update with photo.
Physical Phone Automation Stand
Building a 3D Printer Under 200$
Phone case with built-in MicroSD reader
How to make a mini 3D Cinema for Smartphones and Tablets / i3DG
3D Printed Stepper Motor
Print Conductive Circuits With An Inkjet Printer
Charliecube -- Charlieplexed 4x4x4 RGB LED cube
Dinosaur Coat hooks
Chimera: $60 DLP High-Res 3D Printer
Strandbeest Inspired 3D Printable Walking Machine
Another infinite table
Infinity Mirror Clock
Giant 100mm LED
MX3 - Professional LED Panel
Let your inbox help you discover our best projects, classes, and contests. Instructables will help you learn how to make anything!
© 2016 Autodesk, Inc.