Tell us about yourself!
IoT Air Freshner (with NodeMCU, Arduino, IFTTT and Adafruit.io)
5 Ways to Print on Wood
How to Integrate Wires Into 3D-Prints to Build a 18650 Battery Charger
Design and Manufacture Your Own Enamel Lapel Pin
Floating Shelves From Scrap Wood
Raspberry Pi Zero W IP Camera With Motion & Weaved
Reclaimed Bamboo Box Bluetooth Speaker
Quick Clamp & Release Vice
$15 Motorized Rotating Display Turntable
GLO: IoT Smart Light
Executive Stereo Audio Bluetooth Speaker
TuneCloset Glass Door Automation
Protective Leather Watch Cover
Street Light ON/OFF Schedule With Mobile App.
Wall Switches, Philips Hue & NodeMCU
Automatic Hall Effect Switch
Bench PSU Power Supply From Old ATX With Arduino and LCD Monitor
Make Your Own Bluetooth Speaker
VHS Library Pi Security Camera
Ultrasound Tank Level Meter
E-Paper Weather Display With Photon and IFTTT
Raspberry Pi Radio
Digital UV-meter, With OLED Display. Arduino Project for Beginners
DIY Vintage Streaming Radio With a Raspberry Pi
PiZero AirPlay Receiver
YouTube Subscriber Counter Using an ESP8266 Board
Station number 4 to the 4 button
Super thank you!Have now found and changedOne more question. Can you set favorite stations on the buttons 1-9Would be so right?case 0x10EF20DF: /*(" 4");*/ irStr = 0;Serial.print(F("cli.play("4")\r")); break;
Today I connected my remote control, but the seller has sent me another with the cross below. Now when I switch is key 5 stop and play buttons 4 and 6 volume and buttons 2 and 8 stations Can man change that somehow in the library or ino?
Arduino - Security Panel System With Using Keypad and LCD Display
The Musixel BoomBox
Dodecagon Light With RGB, Lightbulbs and Wifi
RAIN DROP DETECTOR WITH EMAILING USING ARDUINO UNO
Shou Sugi Ban Pine Cutting Board
Hacking a Sonoff Touch Panel to Work With MQTT and Homeassistant
Portable Bluetooth Speaker
Pi Zero W Tic Tac Case
Making a Wooden LED Clock
Bright Shining "Hidden Solar" Security Light
IoT: Weather Box (with Custom Alarms & Timers)
Arduino Fingerprint Sensor Tutorial
Artnet LED Pixels With ESP8266
Stair Lighting With Motion Detection and Following Lights
EAL - Arduino Projekt - Ambilight Tv/Garage Parkering
LightBox Music Visualizer
Guide to Buying Portable Speaker Parts (PART 2!)
My radio has finally earned from 0.96 LCD and Russian tags. Buttons and IR has not done so far. There is one problem, after a while the radio turns off, Stoped on the display, Play through the WEB does not help, just off / on. What could be the problem?Thanks again for such a great project and help!
RFID Door Lock
I am so stupid:) ... Now goes! I could have thought of second cables to connect.Super. Many Thanks!! Now I can test whether it is stable.Thanks again for the support!
Now I understand nothing ... in the u8glibConf.h stands --NodeMcu-- --Mini Pro--Tx RxGnd GndVU RawAnd now you write the tx from mini pro to rx of nodeMcu is not well wired. ?!Have now new cable taken nevertheless the time does not runSo now everything has new, new flashed, new cables and still does not run the time :( what am I doing wrong? ;(
I may take wrong karadio U8glib.ino? I take the ziphttps://github.com/karawin/karadio-addons/blob/mas...
Have now all newly made new Nodemcu new mini pro everything flashed. Oh yes new cables. And nevertheless the clock does not run.What I have yet discovered when Nodemcu is connected to the computer and Termite runs when I enter sys.date command, the clock runs on my small display. However, the time after the reset or new start again away:(
DIY Polarity Led Tweezers
Yes display shows all info ... only the time display hangs
Solar Powered WiFi Weather Station
Have done so and waited. No change. Time still shows 00-01-2000:(
Have all libraries reloaded and set. Go nowMany thanks!!!:)Now I need baud rateset toSys.uart ("28800")I do not understand yet When I start after the fast Termite.exe, I see only hieroglyphs .. I have to set with Termite .exe irgent something?
#define TZO 1 changed to #define TZO 2, reflashed. The time is on 00-01-2000 :( I'm doing something wrong?
I have flashed mini arduino with Arduino Uno and then I tried immediately with Termite exe.Das did not work. Then I put everything together. And over Nodemcu again Termite started and entered Sys.uart ("28800") and that has worked. ;)Now I have only the problem that the time is not true: (and Russian letters are not represented correctly
have all libraries reloaded and set. Now goesMany Thanks!!!:)Now I still need baud rate set tosys.uart("28800") I do not really understand that yet. If I start after the flashen Termite.exe I see only comical pay .. must I adjust with Termite .exe irgentetwas?
Rangefinder for Garage Parking With Arduino
Arduino Parking Assistant
Reverse Car Parking System
"Arduino Pro or Pro Mini, ATmega328 (3.3V, 8MHz)" Arduino: 1.8.2 (Windows 10), Board:Fork / exec C: \ arduino-1.8.2 \ hardware \ tools \ avr / bin / avr-gcc.exe: The file name or extension is too long.Error compiling for the Arduino Pro or Pro Mini board.Wanted to connect, 0.96" I2C IIC SPI Serial 128X64 White OLED LCD but get compile error message .what am I doing wrong?
No errors when compiling display is however dark :(
7 Bi-color LED Matrix Scrolling Text Display
Wifi Webradio With ESP8266 and VS1053 (KaraDio)
Halloween Scene Controller
Wireless Car Parking Alarm
GSM Shield Home Alarm
Arduino Battery Shield
Home Sensor Station
Arduino Watch Sport
Arduino Password Lock
Personalised Word Clock With Animated Time Transitions
ESP8266 Weather Widget
Water Leak Alarm Using LinkIt ONE
Part 2 OpenHAB, MQTT, and ESP Easy - Build Your Own DIY Node
Great Work!!Where did you buy the speakers?