Assembling the Board
Laying Out the Board
Preparing a Schematic
PCB Concepts and Materials
Circuit Board Design Class
Easy Acoustic Levitator
High Speed Photography
Getting Started With NeoPixel / WS2812 RGB LED
DIY CNC Router Build (large Format 5x10ft, Rack and Pinion)
Javelin's Word Clock
Make a Solar Powered Bug Robot
Flip-Top CNC Table
DIY Binary Alarm Clock
OpenVFD: 6-Digit IV-11 VFD Tube Clock
How to Sharpen Used and Dull Drill Bits (By Hand!!)
3D Printer - Working Area 40x40x40cm
3D Printed Laser XY Scanner - Draw, Cut, Engrave, or Scan
Littlebots: Simple 3D Printed Android Arduino Robots
Arduino Based Lightsaber With Light and Sound Effects
DIY Professional 18650 Battery Pack
Tales From the Chip: LM1875 Audio Amplifier
Rocket Ship Panel
PiEyeR Enhanced Thermal Camera
Making SMD PCBs at Home (Photoresist Method)
How to Make a Touch Switch Using One Mosfet
Water Tank Levels by WiFi on Your Phone
IoT Water Alarm
Electrolytic Rust Removal Aka Magic
Manual Bar Bender / Scrolling Tool
Xpider Fatty -- the Smallest Smart Robot Spider in the World
QUATTRO - the Arduino Quadruped Robot
[DIY] Spider Robot(Quad Robot, Quadruped)
Solar Powered APRS Digipeater for Amateur Radio
How to Burn a Bootloader to Clone Arduino Nano 3.0
Tales From the Chip: LM386 Audio Amplifier
RO-V : Remote Operated Vehicle
Control DC and Stepper Motors With L298N Dual Motor Controller Modules and Arduino
Build a Laser 3D Printer - Stereolithography at Home
DIY High Resolution 3D DLP Printer (3D SLA Printer)
Ultimate Intelligent Fully Automatic Drone Robot (w/ RPi, Arduino)
IoT: Raspberry Pi Robot With Video Streamer and Pan/Tilt Camera Remote Control Over Internet
IoT - Controlling a Raspberry Pi Robot Over Internet With HTML and Shell Scripts Only
How I Make Cool Metal Inlays
Splendid work and great technique!!! Many thanks to share!I saw some 18th century pistols with silver inlays in the hard wood. As I believe they didn't had any rotary tool (certainly no laser) do you have an idea how they were making the groove so precise?
Face Detection Security System Using Pi,IBM-Watson,Node-red,Twilio,Email Service
Configuring MKS Sbase V1.x 32-bit Controller Basics and Intro to Smoothieware.
3D Printed Animatronic Eye Mechanism on the Cheap
Android APP to Control a 3DPrinted Robot
EEZYbotARM Mk2 - 3D Printed Robot
Make Your Own High Quality CO2 Lasercutter! With Touch Control!
Tabletop Pull Back Tri-Mode Spring Motor Rolling Chassis
DIY Carbide Lathe Tools for Cheap
Build Your Own Microcontroller
How to Temper Steel
Minimal Arduino UNO (a.k.a. Arduino Pro)
Robot Arm Controller
Controlling Arduino Robot Arm With Arm Link Software
Easy and cheap lab regulator for any PSU
Make your own Arduino Nano (DIY - Arduino Nano)
Raspberry Pi Alamode CNC Controller
Mind Controlled Robotic Arm
Micro Servo Robot Arm
Chaos( Iron Man 2) Swinging Stick( Pendulum Sticks) Perpetual Motion
Building R2D2 From Scratch / Bâtir Un R2D2 À Partir De Rien
3D Printed Smart Watch Dock
The Nerd Watch
Arduino Laser Engraver Wood Design!
Acoustic Tractor Beam
Heatless (cold) Toner Transfer for PCB making
How to Build the Fastest Quadcopter in 3 Hours
Raspberry Pi: Wall Mounted Calendar and Notification Center
DIY Smart Follow Me Drone with Camera (Arduino Based)
How To Make A Raspberry Pi SuperComputer!
Arduino Data Glasses For My Multimeter
3D CNC Relief Sculpture - ArtCAM
Cheap CNC Dos and Don'ts
The Wordclock Grew Up!
PCB designing and isolation milling using only free Software
CNC USB dual layer PCB milling
3D Milling CAM Setup - Fusion 360
Tools and Materials for CNC
Welcome to CNC
Laser Cutting Class
looks very promising. would it fit on the CoreXY?Question, on hat pin do you connect the laser driver? SpnEn? Could you please share your GRBL settings?Best regards.
In the GRBL settings, I had to lower the X and Y max rate to 250 so the steppers do not start to oscillate at hight speed. would there be another setting which could help for better tune? could you show your settings?
Thanks I'll do so.After installing the electronics, I realized that when using the application "bCNC" (what I was planned to use) when I give the order to the laser holder to go up, it goes up-right, or with the order to go left, it goes down-left...and so on... what should I set as parameter to make it work logically?
My mistake, as I flashed 2 Arduino's, one with your file and another with the "flat" GRBL and then I mixed the boards... :-(
Portable CoreXY Laser engraver
Hello again,How do you drive the laser? thru the SpnEn pin? Have you made a driver with some transistor?I use an Arduino uno with a CNC Shield and I bought the laser you proposed..
Bravo, splendid smart project.So I am making it... At the point to add the electronics.I added end points switches, but I do not know here the Zero side (XY) is and I would prefer to know it before entering a home command. Can you help?I saw you added the engraver option, which is absolutely great. my only concern is that I find the shafts supporting the spindle holder not rigid enough for engraving. I would suggest to add another shaft behind the two others... I'll try this in next step...Where can I download your spindle holder?Bravo again and many thanks
Many thanks for your answer, I'll go on with the laser configuration and top there awaiting your new deign...Best regards.