loading
11Comments

Tell us about yourself!

Complete Your Profile
  • Making a Multiboot USB drive (All-In-One).

    Thank You! I was looking for a good "NEW" way to do this with a uEFI system, I have a Dell Tablet that still gives me issues tho, and I'm worried that if I format the Internal eMMC tha it will brick or be unusable, I'm still not good with uEFI, if Anybody wants to teach me I'll send them some bitcoin or tip them with my PayPal. It's important to me that I learn how to install on a uEFI computer, especially x86_64 Tablets, so ANY help from an experianced person will be GREATLY appreciated and rewarded! :) feel free to e-mail me or message me so we can swap contact info's if you can help me... Now that everything is uEFI, I have to learn how to fix the "Root" of the systems. And I'm actually afraid of bricking because these new computers are Very Expensive... I'd rathe...see more »Thank You! I was looking for a good "NEW" way to do this with a uEFI system, I have a Dell Tablet that still gives me issues tho, and I'm worried that if I format the Internal eMMC tha it will brick or be unusable, I'm still not good with uEFI, if Anybody wants to teach me I'll send them some bitcoin or tip them with my PayPal. It's important to me that I learn how to install on a uEFI computer, especially x86_64 Tablets, so ANY help from an experianced person will be GREATLY appreciated and rewarded! :) feel free to e-mail me or message me so we can swap contact info's if you can help me... Now that everything is uEFI, I have to learn how to fix the "Root" of the systems. And I'm actually afraid of bricking because these new computers are Very Expensive... I'd rather learn on my own PC. Thanks Again tho I like the Tutorial a Lot!

    View Instructable »
  • rcochran5 commented on pinchan's instructable Use Your Tablet As Raspberry Pi Screen3 months ago
    Use Your Tablet As Raspberry Pi Screen

    Your format for your IP address is wrong I believe. It should look somethink like 192.168.0.4:21210r 192.168.1.45:21 <-different port (21)Im not exactly sure what :(Port) you want to use with VNC for Pibut I do know that the IP address has to have four sets of numbers seperated by (.) -

    View Instructable »
  • DIY aluminum investment casting using a 3d printer.

    What brand of 3D printer do you use and is it hard to design things? what kind of software would be one of the easiest to use to make things like this?

    Awesome!!

    View Instructable »
  • rcochran5 commented on dreens's instructable Battery Eliminator7 months ago
    Battery Eliminator

    once the Diode is installed the Positive pole will only be at one end since a Diode cuts current in one direction only. if you want to reduce the voltage or amperage you should use a Resistor. That is why there are Diodes AND Resistors. Resistors cause a V drop... not Diodes. Diodes only cause a V-drop when the current is moving Against it. Not With it. What would be neat is if someone would create an inductive Pad to power old battery operated "Things" without a physical power cord. you would need a Transformer, speaker coil wire... enough for the field plate and the receiver, and a bridge rectifier to turn the Inducted AC field into DC current at the device. probably easy to scrap for a Transformer with 25-50VAC for free... then run it through a winding to generate a magneti...see more »once the Diode is installed the Positive pole will only be at one end since a Diode cuts current in one direction only. if you want to reduce the voltage or amperage you should use a Resistor. That is why there are Diodes AND Resistors. Resistors cause a V drop... not Diodes. Diodes only cause a V-drop when the current is moving Against it. Not With it. What would be neat is if someone would create an inductive Pad to power old battery operated "Things" without a physical power cord. you would need a Transformer, speaker coil wire... enough for the field plate and the receiver, and a bridge rectifier to turn the Inducted AC field into DC current at the device. probably easy to scrap for a Transformer with 25-50VAC for free... then run it through a winding to generate a magnetic field and place a coil of wire on top and add winding until the voltage you are looking for is achieved, Usually about 6VDC which would be about 12VAC (pre bridge Rectified)? just a guess, but cool wooden battery anyway no doubt.

    really, you could also just permanently solder in a plug reciever and plug it into the Power Converter whenever the batteries are dead... but most things (not all) have a power converter already.

    apparently not lol

    View Instructable »
  • rcochran5 commented on Malkaris's instructable Mineral Oil Bitcoin Mining for Aquaponics7 months ago
    Mineral Oil Bitcoin Mining for Aquaponics

    Ultra copper from your auto parts store. It seals valve cover gaskets... oil proof. Use that around the pipes before fitting the hose. Good as gold.

    View Instructable »
  • rcochran5 commented on Malkaris's instructable Mineral Oil Bitcoin Mining for Aquaponics7 months ago
    Mineral Oil Bitcoin Mining for Aquaponics

    You really shouldnt mix Oil and water,... the best way to transfer heat between the oil based heat sink and the water radiator would be to use a membrane or Copper Plumbing like Windings of Copper tubing back and forth along the outer surfaces of the inside of the tank where the water could pass through the oil without ever touching it... copper transfers heat from the oil to the water that way... then the water could just flow from the outside world into the copper tubing warming the water and then exit back into the outside world as new water is pumped through.

    I know one thing for sure, I have a 20*16' room and i run a Spondoolies SP20 at a medium high setting (air cooled) and it only takes a couple hours for my room to go from 50F to 80+F... considering that it kicks about $0.50 at me every two to three hours... I think I'll be using that for my heater next year too... since I got it Nov 2015 to 6/8/2016 it's made me $216... my power is $0.09 per KW/H and it pulls +/-800 to 1200 Watts at the wall... so it costs about $1.50 - $2.50 per day but earns about $1 to $4 dollars per day... cant really consider it a loss to make money to heat your house... can you?

    View Instructable »