theRIAA
- Date Joined:May 7, 2006
- Instructables:9
- Total Views:841,117
- Featured %:66%
- Subscribers:115
- Answers:75
- Best Answers %:6%
- Comments:1,038
Instructables 
Achievements
Patches
from
BLUEBLOBS2
Questions
What is the easiest/cheapest way to charge batteries from a wind generator. Asked in Living 3 years ago Answers: 5 |
Best Answers
» you cant reach rubbers' melting point without completely destroying it's vulcanized properties.yo…
» Go to a shooting range and ask if you can pick up all the discharged shells. Take the empty brass…
» *buy a motion detector for lights. *instead of screwing light bulbs in, screw in a light bulb soc…
» go get that material from home depot, put your original car mats over it, outline it with a sharp…
» no... the ignighters have to all be pressed at the exact same time if you want any possible boost…
» Go to a shooting range and ask if you can pick up all the discharged shells. Take the empty brass…
» *buy a motion detector for lights. *instead of screwing light bulbs in, screw in a light bulb soc…
» go get that material from home depot, put your original car mats over it, outline it with a sharp…
» no... the ignighters have to all be pressed at the exact same time if you want any possible boost…
Comments 1-10 of 1018(view all)
» VERY nice job, although I want to see a bright video of it zooming around in the street…
» what are we talking about again...
» what does separating the legs do?
» sweet job. I would have made the bending radius a little smaller so they come out the r…
» sweet! and you can turn the tripod into a flash/laptop holder.
» Humm, that link wasn't under my control. You're free to make the wallet without the pdf…
» horrible job, you can clearly see the edges even in this poor quality. It works better…
» I think control or at least release of the ballasts from inside is necessary. Also key …
» sounds sweet, you should post a picture.
» I'd like to see more recipes (brownies, soup?) but so far this is the only practical ap…
» what are we talking about again...
» what does separating the legs do?
» sweet job. I would have made the bending radius a little smaller so they come out the r…
» sweet! and you can turn the tripod into a flash/laptop holder.
» Humm, that link wasn't under my control. You're free to make the wallet without the pdf…
» horrible job, you can clearly see the edges even in this poor quality. It works better…
» I think control or at least release of the ballasts from inside is necessary. Also key …
» sounds sweet, you should post a picture.
» I'd like to see more recipes (brownies, soup?) but so far this is the only practical ap…
Favorites
Groups
Orangeboard
21
comments
|
Add Comment
|
Hi there theRIAA, i subscribed to you , will you subscribe back?
*IP locate started: 34.576.4453.24 found watch mode selected >locked locate end...
Hey, I read about your paracord key chain, but didn't really get it. Could you possible put up a picture for me? Thanks
May 17, 2009. 11:57 AMThelonelysandwitch
says:
Is that a fenix ld01 flashlight? I wanted to get one of those.
it's a fenix i got before i knew about DX. it's 1 watt something, but I put a 3v nimh battery in it so it's supper bright, and it's covered in electrical tape so i have e tape everywhere.
i'd recommend a AAA flashlight from DX, or really just one of these:
http://www.dealextreme.com/details.dx/sku.1253
they're bright enough for most things.
i'd recommend a AAA flashlight from DX, or really just one of these:
http://www.dealextreme.com/details.dx/sku.1253
they're bright enough for most things.
Thanks for your comment! Hope I did you justice on giving you credit for the idea. I actually got the idea to use coffee bags because I saw some woman still toting around one of those purses made from Capri Sun pouches.
Jan 4, 2008. 12:50 PMGorillazMiko
says:
Hello, and welcome to Instructables!
I have realized that you did not receive a greeting from ewilhelm (Eric) or the Instructables Robot, so here you go!
I do NOT work for Instructables, but I give out greetings once in a while.
Welcome, and just have fun at Instructables.
If you have any questions, you can contact the Instructables staff. If you do not know who they are, you can check them out here. Just click on one of the accounts at the link I just gave you (somebody in the Instructables Team/ Interns/ Advisors) and ask them in a private message or comment.
Have fun!
-GorillazMiko
I have realized that you did not receive a greeting from ewilhelm (Eric) or the Instructables Robot, so here you go!
I do NOT work for Instructables, but I give out greetings once in a while.
Welcome, and just have fun at Instructables.
If you have any questions, you can contact the Instructables staff. If you do not know who they are, you can check them out here. Just click on one of the accounts at the link I just gave you (somebody in the Instructables Team/ Interns/ Advisors) and ask them in a private message or comment.
Have fun!
-GorillazMiko
 |
