http://www.instructables.com Sat, 25 May 2013 14:13:04 PDT BLOX v1.01 http://www.instructables.com/id/Miniature-Radial-Engine-Crank-Case/ http://www.instructables.com/files/deriv/FBP/QG13/H1ZG78EX/FBPQG13H1ZG78EX.SQUARE2.jpg http://www.instructables.com/files/deriv/FBP/QG13/H1ZG78EX/FBPQG13H1ZG78EX.SQUARE.jpg http://www.instructables.com/files/deriv/FBP/QG13/H1ZG78EX/FBPQG13H1ZG78EX.SMALL.jpg Flying_MashedPotatoes Modeled and then milled a crank case out of aluminum using a Manual Milling Machine; with rotary table. Also used a lathe and boring bar. This will be for a compressed air power 8 cylinder radial engine with 0.5"bore and 0.625" stroke.
By: Flying_MashedPotatoes

Continue Reading »]]> Tue, 15 May 2012 18:41:45 PDT http://www.instructables.com/id/Radial-Arm-Saw-Overhaul-Modification-for-Low-Pro/
Radial-Arm Saw Overhaul & Modification for Low Profile Storage - More DIY How To Projects]]> http://www.instructables.com/files/deriv/FRF/2GYT/GH8XYOEO/FRF2GYTGH8XYOEO.SQUARE2.jpg http://www.instructables.com/files/deriv/FRF/2GYT/GH8XYOEO/FRF2GYTGH8XYOEO.SQUARE.jpg http://www.instructables.com/files/deriv/FRF/2GYT/GH8XYOEO/FRF2GYTGH8XYOEO.SMALL.jpg neffk This instructable is about how to overhaul/re-build a Craftsman radial arm saw.  I also included instructions for some modifications I made so that it can be stored compactly against the wall of my 1-car garage. My father recently gave me his old radial arm saw.  It had been sitting in his garage,...
By: neffk

Continue Reading »]]> Tue, 7 Dec 2010 00:39:13 PST http://www.instructables.com/id/Welcome-to-my-Workshop/ http://cdn.instructables.com/FWM/23AU/FNZAF9ZC/FWM23AUFNZAF9ZC.SQUARE2.jpg http://cdn.instructables.com/FWM/23AU/FNZAF9ZC/FWM23AUFNZAF9ZC.SQUARE.jpg http://cdn.instructables.com/FWM/23AU/FNZAF9ZC/FWM23AUFNZAF9ZC.SMALL.jpg guyfrom7up This is my workshop, a lot of the tools are pretty old, but I like it. My workshop consists of my workshop and my electronic lab. There I conduct High Voltage (HV) experiments, as well as intricate circuitry (just don't mix the two!). I really only have wood working tools, but I would like to hav...
By: guyfrom7up

Continue Reading »]]> Tue, 2 Dec 2008 15:39:36 PST http://www.instructables.com/id/Sawsmith-Radial-Arm-Saw-Enlarge-Arbor-Hole-on-a/
Sawsmith Radial Arm Saw -- Enlarge Arbor Hole on a Regular Blade - More DIY How To Projects]]> http://www.instructables.com/files/deriv/FJJ/PURN/FNNJY5CD/FJJPURNFNNJY5CD.SQUARE2.jpg http://www.instructables.com/files/deriv/FJJ/PURN/FNNJY5CD/FJJPURNFNNJY5CD.SQUARE.jpg http://www.instructables.com/files/deriv/FJJ/PURN/FNNJY5CD/FJJPURNFNNJY5CD.SMALL.jpg Phil B A friend has a Sawsmith radial arm saw in good working condition, but getting blades is a problem. A special mount holds the blade on the shaft and uses a 1 1/4 inch hole rather than the standard 5/8 inch hole. The establishment that once sharpened his original blades is no longer in business. I sug...
By: Phil B

Continue Reading »]]> Mon, 17 Nov 2008 14:19:39 PST http://www.instructables.com/id/Sears-Radial-Arm-Saw-Egg-haped-Indexing-Holes/
Sears Radial Arm Saw: Egg-shaped Indexing Holes - More DIY How To Projects]]> http://www.instructables.com/files/deriv/FFX/ZG80/FLQAM12Y/FFXZG80FLQAM12Y.SQUARE2.jpg http://www.instructables.com/files/deriv/FFX/ZG80/FLQAM12Y/FFXZG80FLQAM12Y.SQUARE.jpg http://www.instructables.com/files/deriv/FFX/ZG80/FLQAM12Y/FFXZG80FLQAM12Y.SMALL.jpg Phil B Sears 10 inch Radial Arm Saws were very popular for many years. The motor yoke is shown below with modifications this Instructable will describe. The center hole suspends the weight of the motor and yoke from the carriage on the saw arm. The four smaller holes you see in the photo receive the ind...
By: Phil B

Continue Reading »]]> Tue, 30 Sep 2008 17:41:15 PDT