Instructables: exploring - photos - workshop - cars - featured http://www.instructables.com Tue, 29 Jul 2014 22:29:11 PDT BLOX v1.01 Pull a Car Dent Using a Telephone Pole http://www.instructables.com/id/Pull-a-Car-Dent-Using-a-Telephone-Pole/ http://cdn.instructables.com/F0A/P4OW/GYR35OR3/F0AP4OWGYR35OR3.SQUARE2.jpg http://cdn.instructables.com/F0A/P4OW/GYR35OR3/F0AP4OWGYR35OR3.SQUARE.jpg http://cdn.instructables.com/F0A/P4OW/GYR35OR3/F0AP4OWGYR35OR3.SMALL.jpg hackmattr I bought a car with a major dent on the driver side rear quarter panel and rear door. Instead of buying a door panel and quarter panel, I decided to pull the dent. Using a slide hammer and stud welder was not the best method for this dent removal (Spent a couple days pulling it this way). Seeing n...
By: hackmattr

Continue Reading »]]>
Sat, 22 Dec 2012 01:04:20 PST
Close Quarters Impact Wrench http://www.instructables.com/id/Close-Quarters-Impact-Wrench/ http://cdn.instructables.com/F7I/TNE6/HAQ36VM1/F7ITNE6HAQ36VM1.SQUARE2.jpg http://cdn.instructables.com/F7I/TNE6/HAQ36VM1/F7ITNE6HAQ36VM1.SQUARE.jpg http://cdn.instructables.com/F7I/TNE6/HAQ36VM1/F7ITNE6HAQ36VM1.SMALL.jpg Toga_Dan I was in a tight spot under the hood. Not enough torque on the wrench. Not enough room for a cheater bar, or pneumatic impact wrench. Not even enough room to swing a hammer. The solution?  String a bicycle chain through the closed end of a combo wrench, and through a barbell weight, lock it with vi...
By: Toga_Dan

Continue Reading »]]>
Sun, 16 Dec 2012 01:50:46 PST
Making a personalised car-badge-themed keyring http://www.instructables.com/id/Making-a-personalised-car-badge-themed-keyring/ http://cdn.instructables.com/FY2/23WS/H2MYKB1W/FY223WSH2MYKB1W.SQUARE2.jpg http://cdn.instructables.com/FY2/23WS/H2MYKB1W/FY223WSH2MYKB1W.SQUARE.jpg http://cdn.instructables.com/FY2/23WS/H2MYKB1W/FY223WSH2MYKB1W.SMALL.jpg madmorrie My partner drive a lovely old 1962 Valiant. She particularly likes the design of the boot badge. For Mothers Day this year I decided to make her a personalised key ring based on that design. Also I was itching to try out this 3D printing caper so this was the perfect excuse. Fist up I sketched it o...
By: madmorrie

Continue Reading »]]>
Mon, 28 May 2012 14:13:30 PDT
How to install Halo Projector Headlights http://www.instructables.com/id/How-to-install-Halo-Projector-Headlights/ http://cdn.instructables.com/F89/549H/GZISQR1N/F89549HGZISQR1N.SQUARE2.jpg http://cdn.instructables.com/F89/549H/GZISQR1N/F89549HGZISQR1N.SQUARE.jpg http://cdn.instructables.com/F89/549H/GZISQR1N/F89549HGZISQR1N.SMALL.jpg ilovejdmtoy Installing halo projector headlights is fairly simple, but can take a few hours. This is just a general guide for headlights and might vary from your particular set. For all of our headlights, we always recommend professional installation. Just a few general tips - 1. Wear protective gloves and go...
By: ilovejdmtoy

Continue Reading »]]>
Thu, 8 Mar 2012 11:13:29 PST
Mini Tractor From Go kart parts http://www.instructables.com/id/Mini-Tractor-From-Go-kart-parts/ http://cdn.instructables.com/FIM/9YSO/GQRAVTAQ/FIM9YSOGQRAVTAQ.SQUARE2.jpg http://cdn.instructables.com/FIM/9YSO/GQRAVTAQ/FIM9YSOGQRAVTAQ.SQUARE.jpg http://cdn.instructables.com/FIM/9YSO/GQRAVTAQ/FIM9YSOGQRAVTAQ.SMALL.jpg flyingchainsaw I built this tractor because I go to many tractor shows and festivals where there are lots of cool renovated tractors, huge custom engines, and vintage vehicles.  I had a bad case of tractor-envy, but just didn't have the money (and it is BIG money) to acquire one of these tractors and bring it to s...
By: flyingchainsaw

Continue Reading »]]>
Sun, 31 Jul 2011 19:59:04 PDT
Bullet Shell Valve Stem Caps http://www.instructables.com/id/Bullet-Shell-Valve-Stem-Caps/ http://cdn.instructables.com/FUT/4FN1/GOWNTHOU/FUT4FN1GOWNTHOU.SQUARE2.jpg http://cdn.instructables.com/FUT/4FN1/GOWNTHOU/FUT4FN1GOWNTHOU.SQUARE.jpg http://cdn.instructables.com/FUT/4FN1/GOWNTHOU/FUT4FN1GOWNTHOU.SMALL.jpg Mrballeng The inner diameter of a 40 cal. bullet shell happens to fit nicely over a valve stem cap. All you have to do tap the shell onto the cap with a hammer. These went to the same friend who got the retractable bullet pen. Safety first: The shells were already expended by the time I got them. Never a...
By: Mrballeng

Continue Reading »]]>
Tue, 14 Jun 2011 16:55:35 PDT