Instructables: exploring - stepbystep - green - red - power Sat, 13 Feb 2016 03:02:09 PST BLOX v1.01 Warhammer 40000
Warhammer 40000 - More DIY How To Projects]]> DamiD96 warhammer 40000, scenary. Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Finish
By: DamiD96

Continue Reading »]]>
Wed, 11 Feb 2015 12:14:09 PST
Cheap Drill Conversion
Cheap Drill Conversion - More DIY How To Projects]]> transistor2 This is a super easy way to make your cheap drill run as either a corded or cordless drill, that way you dont have to throw away the battery. It took me about 15 minutes to do it and it can be done with just about any drill. What you will need. Any drill that is battery operated expensive or chea...
By: transistor2

Continue Reading »]]>
Mon, 19 Jan 2015 17:25:15 PST
Simple RGB LED MOOD Colour Potentiometer Without Microcontroller
Simple RGB LED MOOD Colour Potentiometer Without Microcontroller - More DIY How To Projects]]> Avadhut.Deshmukh Display the color combinations of color LEDs without using a Microcontroller you Can Make a Simple Color Cycle Display For RGB (Red,Green,Blue) LEDs What You Need You will Need: 1]1K potentiometer x3 2]330R resistor x3 3]LED Red,Green,Blue x3 4]Battery holder x1 5]Perforated boards PCB 6]Ribbon...
By: Avadhut.Deshmukh

Continue Reading »]]>
Mon, 30 May 2011 01:45:51 PDT
Cold Cathode Light Tube
Cold Cathode Light Tube - More DIY How To Projects]]> QuackMasterDan Time for a replacement or addition to home-lighting? As normal incandescents and compact fluorescents create rather uninteresting color tones , this guide has been created to create a unique and vivid method of lighting up your living areas. Cold Cathodes, or Cold Cathode Fluorescent Lights (CCFLs)...
By: QuackMasterDan

Continue Reading »]]>
Thu, 30 Sep 2010 20:28:13 PDT
LED Star Beam Clock
LED Star Beam Clock - More DIY How To Projects]]> ChromationSystems For this design, some Piranha RGB LEDs are positioned around the outside edge of a clock that hangs on the wall. They are slightly angled so their beams will create a star pattern against the wall as it cycles through approx 16million colors. I am using a clock, purchased second hand, 8x RGB Piranh...
By: ChromationSystems

Continue Reading »]]>
Tue, 31 Aug 2010 23:06:52 PDT
NAR Mods
NAR Mods - More DIY How To Projects]]> ~Aeronous~ I built the NAR, and modded it. The main mods I have made are to the forebarrel and grip area, and the stock. I liked the handle connection points, but the stock itself was too flimsy, even with the hinge inside the handle strengthener mod, so I encased it completely. The main goal was to encase, an...
By: ~Aeronous~

Continue Reading »]]>
Sun, 8 Aug 2010 17:27:13 PDT
Get the RBG LED Circuit from Glowing Ice Cubes
Get the RBG LED Circuit from Glowing Ice Cubes - More DIY How To Projects]]> benthekahn You may have seen those glowing ice cubes before. They glow all different color and have many modes but they are rather expensive ($4-$6 each) and only last for a few hours. I will show you how to extract the circuit and power it with another source.This is a video of the USB light I made with a cir...
By: benthekahn

Continue Reading »]]>
Mon, 16 Jun 2008 23:03:35 PDT
How to clean a laser pointer lens
How to clean a laser pointer lens - More DIY How To Projects]]> grannybasher A very common problem with laser pointers and lasers in general that is easy to fix is dirty lens. I'll briefly explain the two safest and effective methods to clean laser pointer lens.The equipment used in these instructions areA Viper 95mW from Dragonlasers at http://www.dragonlasers.comA lenspen ...
By: grannybasher

Continue Reading »]]>
Sun, 10 Feb 2008 23:28:18 PST