Asked by Thomas1953 on Arduino ATtiny85 Programmer Shield on PCB [ATtinyShield] 45 minutes ago
Just a quick word to say Thanks to everyone who contribute to this site.I work as a teacher in a max-sec prison and I have to produce a lot of my classes with a very limited acces to the web. Luckily, I can acces this page.Instructables has given me a lot ideas and explanations that I have been able to use in my work - and that is all down to the people taking their time to make pictures and produce text to explain stuff to the rest of us.Thanks for that!Ramsing
Posted by BoR13 3 hours ago
Sorry if i misunderstand some of your reply liek for example;my question: did u use a sine wave signal to induced a current to the other coil?your answer: Yes, this is a simple sine wave oscillator.and here is some of your reply: I don't use sine wave generator. My little circuit is a tipycal blocki...
Hi Misan,I have connected everything and put the software on the arduino and if I open universalgcodesender that also gives the welcome message, the only problem is that I don't get the machine running correctly. It reacts very strange to the commands that I give to it. Do you know a way how I can...
Since 2007 I have been answering readers queries here. This is now impossible because questions are burried in a mass of queries from specific instructables.I do not have time to scroll through and find specific questionsSo sorry that's it. No one benefits from my experience and knowledge any more.I suspect this is the same for all of the other regular responders to readers queries.
Asked by rickharris 4 hours ago
That's something I've been planning to do since I couldn't find pegboards in India. While recently moving to a new office, I got a plywood panel put up above the workbench which I plan to drill and convert to a pegboard. Your jig will be most useful.Since you are 3d printing the jig, why not 3d prin...
I'm trying to find out the best method to make a cotton fabric somewhat sticky or tacky ... perhaps the best example of what I am trying to achieve are the identical properties of a 'Football Receiver Gloves'. Criteria:1. Should wash ok without losing its tacky quality. 2. Adhere to itself while avoiding picking up lint or dust. 3. Allow a fabric such as soft cotton to remain soft and pliable.Any help / direction would be greatly appreciated. Thanks in advance."In a sticky situation"
Asked by masotomagic 9 hours ago
I work with an organization that provides books to incarcerated people. All the books we send are donations. (Raising funds for postage is tough enough, so buying books is out of the question.) We get frequent requests for How to Draw books which are rarely donated. Would it be acceptable for me to print Instructables posts on this topic?
Asked by judyspak 11 hours ago
Here's the code with the errors removed://Code by Hunter Knott and based off of Owen Sobel's Bluetooth 4.0 code//Updated by Isaac Burton#define in1 5 //L298n Motor Driver pins#define in2 6#define in3 10#define in4 11#define LED 13#define ena 9#define enb 8int command; //Int to store app command stat...
Toilet bolts are fine, I suppose. However, they do sell T-bolts for this application - search for "POWERTEC QTB1002 Tee Bolt" (or T-bolt) on Amazon and elsewhere. They don't come with the break-away feature found on the brass Toilet bolts. They also come in 1/4" and 516" inch diameters and are rathe...
Asked by kaelcabezas on Marauder's Map - With Hidden Footprints! (Full Size Replica) 16 hours ago
Hi,thanks for this very detailed and very good instruction.Some remarks:- You do not need to modify the sensor. The trick is: as you switch on/off the sensor ground (PWM), you have to switch the sensor (and therefore the heater) 100% on to read the value. This means, you can not read the value durin...
Asked by sadeesh+embedded on DIY Autonomous Line Tracking With Obstacle Avoiding Robot (Rover) 17 hours ago
Hello I'm using the program that you left in the post and when it reaches the curve the robot does not double simply continue straight, I wanted to know why it happens I have to calibrate in the program so that it does not happen, thank you very much
Asked by FabriiD on Line Follower Robot With Arduino - Very Fast and Very Simple 19 hours ago