10551Views20Replies

Author Options:

Sound level meter? Answered

Does anyone know how I can build a simple sound level meter with a light that will come on at a certain sound level?

20 Replies

user
iceng (author)2015-11-22

I seriously do not think you understand or read the LM3915 or 16 PDF.

This IC takes any audio signal and lights a dot (led) according to audio amplitude http://shop.fiberopticproducts.com/index.php?route...

Then an instructable https://www.instructables.com/id/LM3915LM3916-VU-Me...

You will need an opto-isolator on each channel with the outputs in three parallel groups. For your easy, there are more pictures, including the marvelous quad IC.

There is no Best Answer for me here when you hijack an old question... A full schematic design takes more time then I want to allocate...

Select as Best AnswerUndo Best Answer

user
iceng (author)2012-01-28

Years ago I designed a classroom  traffic light always green then yellow
as the noise went up to a preset level and Red when too much  with a
beeper for a pilot school program that did not appear to work,
as I never was contacted to replicate the prototype.

A

Select as Best AnswerUndo Best Answer

user
dessxx (author)iceng2015-11-21

iceng do you have the electronic schematic of this project!!

Select as Best AnswerUndo Best Answer

user
iceng (author)dessxx2015-11-22

That was before cad schematic capture programs and those files are long ago gone.

Today I would use a dollar piezo mike to provide an audio signal to the LM3915 operating in dot mode and place some optical isolators to control what you are after.

Select as Best AnswerUndo Best Answer

user
dessxx (author)iceng2015-11-22

thank, but I have a question how do I split in three different channel green yellow and red? At the end I need three output to light three small light bulb! DC light bulb if possible!

Select as Best AnswerUndo Best Answer

user
aelias36 (author)2012-01-27

Op amps:
http://www.youtube.com/watch?v=TQB1VlLBgJE

Comparators:
http://www.youtube.com/watch?v=y0Q0ERSP24A

Watch the two videos, and build the circuit in the second. Go ahead and ask about anything you're confused about.

Select as Best AnswerUndo Best Answer

user
pennsteve (author)aelias362012-01-27

What I need is to keep a group of kids from getting too loud. If they get to a certain decibel level I want a light to come on to show them they need to quiet down. lol

Select as Best AnswerUndo Best Answer

user
ceekoke (author)pennsteve2013-07-22

This is a bit dated, but wondering if you found a solution. My son has a hard time knowing when his voice is too loud (way too loud). Would love a sound meter that would let him see how loud he is.

Select as Best AnswerUndo Best Answer

user
thegeeke (author)pennsteve2012-01-28

I tried something similar when I was teaching rock climbing. Since I needed to be able to hear the climber I was belaying, it was a safety issue. No matter what I tried, nothing worked like shouting "QUIET!!!!!!!!" :) The light idea probably wouldn't work because when they are talking, they are distracted, and will not be looking at a light. A siren might work, but I really doubt it. :(

Good luck keeping the DB down! :)

Select as Best AnswerUndo Best Answer

user
kelseymh (author)pennsteve2012-01-27

And that's really going to work ... how?

Maybe if you replaced the lights with high-voltage (aluminum foil) sheets on each bus seat....

Select as Best AnswerUndo Best Answer

user
canucksgirl (author)2012-01-27

ok then... Here's an instructable to create a light that comes on with sound. You can apparently adjust it so the light comes on at the sound level you choose.

Select as Best AnswerUndo Best Answer

user
pennsteve (author)canucksgirl2012-01-27

Unfortunately no. It is for a school bus and has to be DC. :-(

Select as Best AnswerUndo Best Answer

user
canucksgirl (author)pennsteve2012-01-27

I found you a link but it's not letting me post it properly. I'll send you a PM.

Select as Best AnswerUndo Best Answer

user
pennsteve (author)canucksgirl2012-01-28

I got the PM. Thank you. I'll have to look into that.

Select as Best AnswerUndo Best Answer

user
canucksgirl (author)pennsteve2012-01-28

No problem. Let me know if you need more help. :)

Select as Best AnswerUndo Best Answer

user
canucksgirl (author)canucksgirl2012-01-27

I sent it, you should have it in your inbox.

Select as Best AnswerUndo Best Answer

user
canucksgirl (author)canucksgirl2012-01-27

Will this work for you or do you need more help?

Select as Best AnswerUndo Best Answer

user
Re-design (author)2012-01-28

Try something like this.

Where it's labeled audio input, use a cheap portable, adjustable amp. and mic.  This amp and mic will pick up the noise and you adjust it to turn on your lights at the level you like.

You can sub one or more of the leds with the indicator lights that your kids will see.  You may (probably) will have to add a transistor or relay to carry the current of the larger light so you don't burn up your chip.

Select as Best AnswerUndo Best Answer