Introduction: Xbox 360 Console Controller Game and Guide / Magizine Stand

By

This is a stand I made for my xbox 360. On the bottom it holds the 360 in the compartment above is space for game guides or magazines. above the magazine holder is the a shelf to hold16 games this can be changed by adding or subtracting layers. on the very top is a controller holder the top can hold 1-3 controllers and a wired headset in the very back.
parts
rods
green 60
white 51
yellow 127
blue 77
red 32

spacers
gray 20
blue 4

connectors
white 26
red 30
yellow 23
green 6
purple 107
blue 62
light gray 6
dark gray 70
orange 12

parts without doors on front
rods
green 52
white 41
yellow 127
blue 69
red 30


connectors
white 16
red 22
yellow 15
green 6
purple 107
blue 62
light gray 6
dark gray 70
orange 8

Step 1: The 360 Compartment

1 this is the base of the stand
2 another view
3 this is the top of the compartment
4 put together like so
*note to get the 360 in some of the front peices will need to be removed to make room to slide it in
parts

rods
yellow 50
red 46
blue 10

connectors
white 14
yellow 2
purple 38
blue 10
dark grey 4

Step 2: Magazine Holder

1 this is the top part of the mag holder it will be added on top of the console compartment
2 add these to the under side
3 this is the door for the mag holder
4 attach the top using the blue rods
5 the 2 grey connectors are added to the 2 blue rods to add support
6 attach the door to the mag holder
parts

rods
green 8
white 11
yellow 9
blue 21
red 4

connectors
white 2
red 16
yellow 5
purple 13
blue 11
orange 2

Step 3: Game Rack

the game rack can be changed to the amount of games you own by adding or subtracting layers but by doing this the doors on the front have to be changed or just taken off if you would rather not fool with it my door is designed to cover 4 rack panels
1 this is the panel needed just make how ever many you need 1 section holds 4 games the top of the magazine area is the bottom of the game rack so for every panel you make you get 4 more spots for games
*note the very top one needs to have the corners sideways as shown on pic 10 in step 6 also this picture is taken upside down to show the green connectors those connect to the magazine area
parts lists bellow list one panel
middle panel parts list

rods
green 11
white 10
yellow 14
red 4

connectors
yellow 2
purple 12
blue 12
dark gray 6

top panel parts list

rods
green 11
white 10
yellow 14
red 4

connectors
yellow 2
purple 19
blue 5
dark gray 6

Step 4: Controller Holders

you can put 3 of these on the top if the stand possably a fourth on the back if you dont put the box from the power cord there

parts per controller holder
rods
yellow 4
blue 2

connectors
red 2
green 2
light gray 2
dark gray 14
orange 2

Step 5: Game Rack Doors

This part is optional if you dont have the parts or dont want to fool with is skip ahead
or just make this and continue

parts
rods
green 8
white 10
blue 8
red 2

spacers
gray 20
blue 4

connectors
white 10
red 8
yellow 8
orange 4

Step 6: Putting It All Together

skip 7 and 8 if you didnt make doors
1 add the magizine compartment peice
2 this is the back wall of the magizine rack
3 add the door to to the magizine compartment to the corners
4 stack the panels on top of each other untill you have the amount u wanted
5 add the main controler peice to the yellow rods the front middle or the midde sides
6 add the other 2 small peices to the middle whites or the back yellow sides
7 conect the 2 peices
8 add the red conectors to the top and bottem yellows
9 the doors are closed in this picture but i had put them on upside down so make sure the yellow conectors are on the bottem
10 finished product