8 SHOT KNEX HAND GUN REVOLVER

Hey everyone im extreme builder and this is my new 8 shot hand gun revolver. This is one of the first decent revolver guns i have seen but im not sure. Now for the range it sometime shoots 20 feet and others 40 feet u never know. im going to be posting a video soon to and that will explain the gun a little more. please everyone be nice because it takes anywhere from 5 to 10 hours to take the pictures and the instructables so if you guys start getting nasty ill just stop posting my guns. If you guys have any questions just ask and ill answer it probably the same day. thanks and enjoy!!!

and please RATE and COMMENT!

PARTS LIST
327 but because u can make the revolver how ever u want this number can change by alot

look at my 12 shot knex gun
https://www.instructables.com/id/extreme_builders_12_shot_knex_gun/

hey everyone,
check out my youtube page
http://www.youtube.com/user/KNEmovies

Step 1: Handle

handle parts

-10 yellow connectors
-4 gray two slot connectors
-6 green rods
-3 blue rods
-4 black Y connector
-4 blue spacers
-6 white rods

TOTAL
37

Step 2: Trigger

trigger parts

-1 gray two slot connector
-2 green rods
-3 blue rods
-4 blue spacers
-4 white rods
-2 green connector
-3 gray spacers
-2 yellow rods
-2 red connectors

TOTAL
23

Step 3: Body

body parts

-8 white connectors
-4 yellow connectors
-3 red connectors
-2 green connectors
-3 gray two slot connectors
-8 white rods
-6 blue rods
-16 green rods
-4 gray spacers
-12 blue spacers

TOTAL
66

Step 4: Barrel

barrel parts

-5 red rods
-2 white connectors
-12 yellow connectors
-2 green connectors
-6 green rods
-1 white rod
-2 gray spacers
-2 blue spacers
-3 gray one slot connectors (one moded)

TOTAL
35

Step 5: Firing Pin

firing pin parts

-1 red rod
-1 orange connector

TOTAL
2

Step 6: Revovler

revolver parts

-64 gray two slop connectors
-64 green rods
-13 white connectors
-8 yellow rods
-8 black ball joint connectors
-3 gray one slot connectors
-2 blue spacers
-2 tan rod connectors

TOTAL
164
u can make the revolver how ever u want this number can change by alot by making more gaps

Step 7: Put It Together

ur DONE

Comments

[guyknex]

too many pieces- could you make it much smaller? i built one with only 94 pieces and it still revolved, but with a rubber band. it still could shoot 30 ft. and had 8 shots!

[daredevil499]

May I use this revolver on my new gun, I am going to post it soon.

[paddyback]

what is a tan rod

[Metalbox]

reinforced red rod

[KnexMaster51]

The 'tan rod connector' is the little tan coloured piece with a small rod on it. Shown in the bottom picture :)

[knextreme1996]

I did make an alternative revolving mechanism for this gun because I didn't want to cut one of my grey connectors. It locks into place when you turn the revolving part of the gun. I strengthened the barrel end of the gun because it requires a little force to lock into place, but it still works. I also modified the handle around the way I hold the gun. However, I still needed to sharpen the firing pin for it to fit through the ball joint. But I have loads of grey rods, so yeah! Great gun by the way! :) It shoots fantastically and is really easy and fun to make! Would it be possible to get permission from extreme builder to upload my own instrutable of this gun with my modifications? I will give lots of credit. :D

[blacktails]

EVERYONE LISTEN, ITS ABOUT THE BALL JOINTS

Look; The black ball joints are used to hold the bullets in place so they DONT fall out the back, they help A LOT.

You connect them directly to the White "Full moon" connector. You put them right on the side of the connector

[sharpbike123]

Could you change the trigger.

[akivaweil]

needs revolver

[KNEX GUN BIULDER]

this is the instructions that you aint under standing lol

[tytiger33]

It's not a true revolver, it's a pepper box gun. Look it up and see why they aren't made much any more.

[epicbobman52]

could i put the turet from this gun on your revolver? https://www.instructables.com/id/Knex-Turret-Pistol/

[joshimcoop]

great gun

[ElvenChild]

Hi

[me is assisin]

the lock on the spinning barrels is easy and pretty smart 4.5*

[lukewilliams010]

looks like a nerf gun :P

[randomknex]

where is the revolver?????? can you please reply asap? thanks

[ske66]

can u mold the piece by putting it in a microwave or a kettle so that u can mold it into place?

[moishyb]

I made it without the ball-joint connectors but i think it decreases the power and also you have to load the gun every time you want to shoot. could someone make a vid explaining how and where to connect the ball-joints? :)

[SteelBeast]

Where can we find the Modification used in the video with spinning free?