This is a very easy project.

Supplies

1x ARDUINO
1x 3.5mm JACK
SPEAKER FOR OUTPUT

Step 1: Connection

Speaker
+ve - Pin 3
-ve - GND

Step 2: Coding

#include "talkie.h"

Talkie voice;
const uint8_t spCHECK[] PROGMEM ={0x0E,0x98,0xBD,0x32,0x03,0x11,0x60,0x00,0x73,0x1E,0x23,0x0E,0xD9,0xCD,0x33,0xC7,0xEC,0x74,0xA7,0x3B,0x9F,0x55,0x6F,0x7C,0x03,0x00,0x16,0xE0,0x00,0x06,0x30,0xF0};
const uint8_t spPLEASE[] PROGMEM ={0x0E,0xC8,0x81,0xD4,0x01,0x59,0x9B,0x8F,0xB0,0x48,0x69,0x57,0x73,0x3B,0xD2,0x24,0x2D,0x3D,0x24,0xCD,0x4A,0xBD,0x33,0x8F,0xF0,0xC7,0x3B,0x6B,0x79,0x4D,0x86,0x9C,0xFE,0x64,0x56,0xA3,0xAA,0x59,0x89,0x3D,0xBE,0xCC,0xA6,0xB7,0xA5,0xCF,0x9D,0x85,0xA5,0xDE,0xE6,0x3E,0xF5,0x29,0xB1,0x98,0xC5,0xE3,0xD2,0x07,0x13,0x10,0x56,0x1D,0xCB,0xF0,0x35,0x87,0x51,0xAE,0x75,0xC0,0x04,0xAC,0x06,0xF8,0x46,0xCD,0x00,0x3F,0x1A,0x19,0xE0,0x7B,0x0B,0x01,0x7C,0xA7,0xF6};
const uint8_t spSEES[] PROGMEM ={0x08,0x30,0x2C,0x45,0x01,0x3F,0x87,0x7B,0xC0,0x03,0x11,0x88,0x80,0x03,0x8E,0x09,0x1B,0x49,0xB2,0xA6,0x66,0xD1,0xE9,0xC4,0xCD,0x87,0xA2,0xCB,0xD7,0x95,0xF4,0xE8,0x0C,0x11,0x6F,0x77,0x3A,0xB3,0x59,0xF5,0x6A,0xB4,0xBD,0x95,0x02,0xCB,0xB6,0xD2,0x97,0xCA,0x82,0x51,0x4F,0xCA,0x90,0x0A,0x8B,0x58,0xBD,0xCD,0x7D,0x1A,0x62,0x62,0x91,0xC8,0xC7,0x69,0x08,0x91,0x55,0xB5,0xEE,0x84,0x3E,0x68,0x53,0x75,0x5F,0xA1,0x80,0x04,0x34,0x3D,0x60,0x01,0x09,0x50,0xE0,0x01,0x00,0x00};
const uint8_t spTHE1[] PROGMEM ={0xA9,0x73,0x5E,0x93,0xC9,0x53,0xC7,0x6E,0xB4,0xC9,0x6A,0xBB,0xE9,0xD6,0x5B,0x9D,0x2A,0x3A,0xEF,0x64,0x6F,0x7A,0xAB,0x55,0x45,0xEF,0x93,0xEC,0x49,0x5B,0x6D,0x72,0xA7,0xD1,0x5A,0x49,0x4D,0x72,0x1E,0x8E,0x6A,0xE9,0x01};
void setup() {
// put your setup code here, to run once:
pinMode(LED_BUILTIN, OUTPUT);
}

void loop() {
// put your main code here, to run repeatedly:
digitalWrite(LED_BUILTIN, HIGH);
voice.say(spPLEASE);
voice.say(spCHECK);
voice.say(spTHE1);
voice.say(spSEES);
digitalWrite(LED_BUILTIN, LOW);
delay(897000);
}