All Pic Programmer

Introduction: All Pic Programmer

Step 1: Parts

Step 2: Schematics

Step 3: PCB Making

Step 4: COMPONENT PLACEMENT

Step 5: FINISH

Epilog Challenge

Participated in the
Epilog Challenge

Be the First to Share

    Recommendations

    • Battery Powered Contest

      Battery Powered Contest
    • Plywood Challenge

      Plywood Challenge
    • Plastic Contest

      Plastic Contest

    81 Discussions

    0
    abuhassan
    abuhassan

    4 years ago

    sorry am new here, where is the part list?

    0
    Chaos_Lord
    Chaos_Lord

    7 years ago on Step 1

    What voltage are the c1, c2, c3 caps supposed to be?

    0
    daz7691
    daz7691

    7 years ago on Step 3

    Hi, i cant get the link 2 work at all.. have u the board in eagle cad if so can u send it 2 me please??? Regards Daz

    0
    chetancc
    chetancc

    7 years ago on Introduction

    Hi,
    I want to program PIC12F629 with readymade .hex code. Which programmer should I use? I would like to know the best and cheapest programmer available. I bought PICKIT2 clone from India but I had very bad experience with it. I couldn't program with it.
    Can you please suggest me good programmer?
    Regards,
    Chetan

    0
    franky975
    franky975

    8 years ago on Step 1

    Hi to all. I have got all of the parts but the c1,c2,c3 - 100nF caps don't seem to be look like yours on the board. Are they 100nF ceramic caps or i have missed something?
    Thank you. Franky.

    0
    shobo
    shobo

    8 years ago on Introduction

    can it be adapted to work on smd ics?i mean the pins can be connected with wires or something

    0
    jomar_00012
    jomar_00012

    8 years ago on Introduction

    Can it program a PIC16F690? Please reply.. i'm going to build this.

    0
    talh
    talh

    8 years ago on Introduction

    plez give me all material of all pic programmer . to make it in house

    0
    SelfCheck
    SelfCheck

    8 years ago on Step 4

    What is JP1? It isn't in the schematic

    0
    Higgs Boson
    Higgs Boson

    8 years ago on Introduction

    Would you be able to use a rs232 to usb adapter for with this programmer? or would there be a way to use a usb be jack rather than the rs232?

    0
    Cartago
    Cartago

    8 years ago on Step 4

    Hi, I use for programming "Proton Complier" but when I connect the PCB to my computer, the program says: -Please reset the target microcontroller in order to access the bootloader process- How can I reset the targer?
    And other question, which is the use of JP1?

    Thank you and you've made an amazing instructable.

    0
    BADelectRonics
    BADelectRonics

    8 years ago on Step 4

    HELLO bro !
    thanks for the very nice programmer , i wich know why you added the connector jp2 ? i mean , for what it is used ?. One more question please , can i uses this programmer for an adaptor USB--->serial ? because i have a laptop not a desktop.
    thank you againe !

    0
    mmajor
    mmajor

    9 years ago on Introduction

    please upload the pcb file again or send it to me

    0
    mmajor
    mmajor

    9 years ago on Step 3

    please I cant open this file please help me any way

    0
    ieye-tech
    ieye-tech

    9 years ago on Step 2

    I made a JDM based programmer [JDM programmer 5v2] it works well on all old computers. But my Pc's Serial port voltage is only around 10 v its not working on my pc.Shall i useful this circuit for my PC.????

    Thanks

    0
    nedim155
    nedim155

    Reply 9 years ago on Introduction

    i think it should work because it works for me with an USB to serial cable :)

    0
    ieye-tech
    ieye-tech

    9 years ago on Step 2

    I made JDM based programmer. it works well on all other old computers. when i checked my seial port voltage its only around 10v. shall i useful this circuit for my PC??

    Thanku.