DIY Dual Woofer Setup (Hidden and Underseat)

Introduction: DIY Dual Woofer Setup (Hidden and Underseat)

About: Necessity is the Mother of Inventions they say, I live in challenging land called INDIA. where the Sub par conditions like power issues, heat, Dust and environmental factors are just tough! and They have force…

"Necessity is the mother of invention" They say.
When I got my New SUV (Mahindra XUV 500), I had not one, But TWO Necessities...

First need was BASS! I can't live without any. Provided that I have a 15 inch Monster SUB at home with 11 Speaker custom Sound system. I was spoiled.

Second need was ability to get decent bass IN my SUV. As you'll see, there's no space at all for conventional woofers at all!
(Spoiler- For those who can't wait, 3rd pic is what we want to achieve. Click it for a glimpse!)

Onto the next page...
Car Ownership and Review thread-

LED Fog Lights and other Mods-

Step 1: Calling Mr.Brain!

XUV 500 is a 7 seater, Good looking SUV but has hardly any boot space with all Seats up.
That's where the need for Mr.Brain Comes in!

Since installing conventional 12 inch or so subwoofers are out of question; I needed something Small and Discreet yet powerful enough to get nice Bass. I am not a fan of Doof-Doof bass. I don't want to blow my ears out. I dont want my neighbours to eavesdrop on my fav music. Just the right amount that makes music alive.

Step 2: Finding Gold Mines

Hunting for the already rare space in my SUV, I narrowed down to a crevice below the middle row seats.
There is just the perfect space for two tiny subs. Another advantage is that the install location being in center of the car, gives even, balanced bass all amongst the vehicle. With conventional setup, I see the rear seat occupants complaining too much bass whereas the first ones can't seemingly get enough of it. This location solves everything.

The space dimensions are about 14" X 12" x 5"
Just what the doctor ordered for a small woofer box!

Step 3: What Woofer?

Here is the hard part, Selecting an appropriate woofer.

After making a trip to various shops, i was both happy and sad.
Firstly some Compact, Under seat woofers were available. Sadly, they all Land above 10,000 Rupees.

Here are a few examples-
JBL 14,000 INR

Ground Zero 12,000 INR

Step 4: I Don't Have That Amount of Money!

Once you get hold of Knowledge, There's nothing like car speaker/Home theater or Car amp/ HT amp or This speaker that speaker. You can use any and many combination of these and with some tweaking, you should get satisfactory sound. I have used Car Systems (HU and Amps, Speakers) in Home and installed Computer 7.1 in cars. Of course, a layman will prefer to simply buy the well known stuff and enjoy peace of mind. But it was not the layman who invented something extra ordinary eh?

Speakers are nothing but fancy air pumps. Their rhythmic movement action on the air generates the sound that we listen. That makes the cone area important, More cone area- More air is moved in each stroke. There are many other parameters like T/S but that's a very wide topic now.

So I thought, why not?

Quickly, I salvaged a pair of subwoofers from old Home Theaters. They're 6.5 Inch, 4 Ohm.

Taking Inspiration from the Underseat woofers from Big players in the market, I set off to brainstorming a specifically sized Box and driver combination that would work just as well, Minus the expensive price tag. A Big Plus is a jump in my DIY list and some Boast-Gun ammo stock!

Step 5: Box 'em and Fix 'em

Having the dimensions and Woofers in Hand, I set out to make appropriate boxes for the little beasts. The size of Boxes for me worked out to be 12" X 10" X 4"
Enjoy the pics!

Materials Needed-
MDF sheets or plywood
Woofer Grilles
Speaker wire

Steps to make Box-
1>Take your measurements
2>Then mark the sheets
3>Cut them
4>Paste them
5>Glue the joints and seams
6>Use Jig saw to cut holes for woofer
7>Attatch some speaker wires to woofer, Drill a hole in box, get the wire out
8>Fix the woofers with screws and put on the Grille
9>Paint the box if you feel like.

There are many good instructables about how to make speaker boxes.
Here are a few-

Step 6: Put Them in Place, and Lend an Ear (Or Two!)

I simply tucked the Boxes under the seats and zip tied the cables. You may want to drill and Fix them but be extremely careful as there can be wires and fuel lines underneath! Refer your Car's User manual or consult the service center.

For me, the friction was good enough to hold them in Place.

Lo and Behold! Here is your all new, Flaunt worthy Dual woofer setup. Small, Hidden and ample output. The smile on your face explains everything. But wait ! The best is yet to come!

Prices- (Indian Rupees)
Boxes (total) 1,500 INR
Woofers (free for me) but in market 1,400 INR (700 per piece)
Misc (Wires and stuff) 100 INR

Total Cost 3,000 INR.(For TWO woofers)
Market Cost 20,000 INR !!

Enjoy and Don't forget to comment.

Be the First to Share


    • Block Code Contest

      Block Code Contest
    • Cold Challenge

      Cold Challenge
    • Baking Contest

      Baking Contest



    2 years ago

    Please tell me something about amplifier you used, or any idea about custom amplifier


    5 years ago

    Nice innovation. I agree, speaker is a speaker. I too use raw drivers in car, not the so called car specific drivers

    Zen Innovations
    Zen Innovations

    Reply 5 years ago

    Thanks. Please post about your system and mods if possible.


    Reply 5 years ago

    My 12-year-old Tata Indica audio system uses the following equipment:

    EClipse CD7200 MKii 3-way active head unit. Dayton Audio Reference RS180.4 7 inch midbass, Dayton Audio RS100.4 wideband midrange, Dayton Audio Air-motion mini AMT Tweeters, 10 inch Infinity Kappa 10 inch subwoofer, Two Pioneer GM-X944 4-channel amplifier, Kenwood KOS-300 for playback from USB drives; MX Reference 75ohm 6-channel digital coax cable as interconnect; Monster RCA splitter cable; Entec 16awg multi strand OFC speaker cables, one 150 amp fuse block near the battery and one power distribution block near the amps; 4 guage wiring used all over; Suede mat on entire dashboard to absorb secondary reflections from the windscreen. Tarfelf sheet damping on both front doors and boot.

    Total investment Rs. 60,000

    The midbass is installed in a fiberglass enclosure with two 18 inch spacers on the front doors, the midrange and tweeters are installed in a 1.6 liter fiberglass enclosure on the far left and right corners of the dashboard in an on-axis position to the drivers seat. The subwoofer is in a 0.8 liter enclosure in the boot along with the two amplifiers. No rear speakers

    The crossover is set on the head unit as follows; Midbass 80 - 315hz (slope 18db on HPF and 12db on LPF); Midrange: 315hz LPF to infinity at12db; subwoofer 80hz LPF at 18db; Tweeters: 9khz HPF at 12db slope.

    Outsourced fiberglass moulding, rest all other work including sourcing equipment, wiring, fixing of HU and amps and tuning done by self.

    ice pio.jpgmaxresdefault.jpgraw mould.jpgthe final enclosure.jpgmidbass.jpgwith grill.jpg

    the amp is jbl gt646. it's placed under the driver seat. do put your project pics if you make one mate!


    9 years ago

    Hey man, gonna build myself a subwoofer box like yours, just wandering what you did for amplification? Did you buy or make an amp? Or does your stereo have amplified sub outputs? Cheers