My long-awaited dragunov. It took a few more days than planned to make the instructable, but it turned out good. It's my biggest instructable yet, and my first sniper. It turned out VERY good. It looks great, AND it shoots great!
let's get to the pros and cons.
IT ACTUALLY SHOOTS HARD FOR A RAM-ROD SNIPER! (65 feet)
Good looking (of course XD)
a little flimsy
scope kinda gets in the way of the pin when you are pulling it
This gun is pure awesome so I suggest you make it right now!
*Some adult assembly required.
Step 1: Stock
The stock, complete with comfy headrest! (X2)=make twice if you don't know.
1: What you are going to make!
2: Make this panel. (X2)
3: make these things with your knex
4: make this stuff....
5: get these.... From where? The fridge!
6: Add 12 blue rods and an orange connector to one of your panels
7: get ONE blue rod.
8: What you should have.
9: add the things you see.
10: add some more stuff..
11: add the last stuff!
12: Put on the last panel and get to the next step!
Step 2: Front Half of Fake Barrel
Title says all. This is just for looks.
1: What will be made.
2: make this (X2)
3: make these, don't forget the white rod.
4: make these things...
5: add 6 blue rods
6: connect those three things and put them on the panel with blue rods.
7: add those things on
8: add the last panel and you're done!
Step 3: Back Half of the Fake Barrel
Don't worry, it's not hard to make, I just took a lot of pictures to make it very clear.
1: What you'll make
2: make this (X2)
3: Make this long thing.
4: Make this (there's another view)
5: Another view.
6: Make this stuff.
7: Build that.
8: add that last panel
9: make that
10: get a tan clip.
11: Make these
12: Add 4 blue rods to one panel.
13: What you should have.
14: Put this on (there's another view)
15: another view
16: put those three things on.
17: slide the blue rod with the tan clip on it in there.
18: slide that on
19: put the last panel on!
20: add the tan clip
21: put that long thing on
22: it's done!
Step 4: Break!
Step 5: Body
What a perfect thing to build right after a big nap! (you need 3 broken white rods, and an optional broken blue rod. An orange connector without tabs on one side is also needed. The blue rod makes it comfortable.)
1: What you are going to make.
2: Make the firing pin! (read note)
3: Make this (X2)
4: Make the trigger..
5: What you are going to make right
6: make/get all of this.
7: add the white rods
8: put that on
9: Add thaat...
10: and put the wheels and the blue rod on.
11: now you're going to make this.
12: make this (X2) and get those rods. (put a bit of scotch tape on the white rods.)
13: Make this
14: make those
15: get this
16: Add 8 white rods, one blue rod, and two broken white rods.
17: Add those things
18: put in the rods from before and put on that long thing
19: add that piece
20: Add the other panel you made and you're done that thing.
21: Make this thing.
22: add two blue rods, and two grey spacers on on of your panels.
23: put that on!
24: put the trigger on (there's another view.
25: Where the white rod should be. (read note.)
26: attach the handle
27: Put that piece there.
28: add the last panel and put the pin in.
Let's put your dragunov together!
Step 6: Putting It Together
1: All the parts
2: put a blue rod in the stock and get it ready.
3: attach stock.
4: pull it up and attach there
5: click those on
6: how it should look
7: get that and take off the parts shown.
8: attach it!
9: add the parts you took off
10: what you should have
11: get this part ready
12: put it like that.
13: Clip it in.
14: YOURE DONE! Now let's make the scope!
Step 7: Scope
Lots of views. It doesn't have to be the exact same as this.
Step 8: Extras and Bands
Title says all.
1: make the mag push and get a stretchy elastic
2: get a #64
3: double it up and put it there.
4: get lots of #64s to power the gun
5: Get one for the trigger
6: put a band on the trigger
7: mag push in and elastic on.
8: other side
9: put the scope on
10: put the pin in and add some elastics where shown!