Introduction: Electro Magnet
DO NOT PUT THIS UP TO THE COMPUTER SCREEN OR IT WILL TURN PURPLE, SHUT DOWN, NOT REBOOT FOR ABOUT 5 HOURS, AND MAY DISABLE INTERNET. I AM NOT RESPONSIBLE FOR THAT. You will need a battery, nail, and about a foot of copper wire.
Step 1: The Nail
Follow the pic. and make sure wire is wrapped so it is touching nail.
Step 2: Finish It Off...
Follow the pic.
You have made an electro magnet!!!!
Thanks to my school for teaching me this!!!
20 Comments
14 years ago
This is a great Instructable, but you need to add a main image of the final project to the intro step. Please do that and leave me a message when you have so that we can publish your work. Thanks!
7 years ago
great instructable I love it
9 years ago
Can it work with a paper clip
13 years ago on Introduction
its really good but coundnt you get zapped if you put uninsulated* wire on it
Reply 10 years ago on Introduction
you're not going to get zapped by 1.5 volts
13 years ago on Introduction
Hello. This is a great instructable and exactly what i was looking for but I have a few questions.
1.) Does the guage of the wire affect the magnetism?
2.) Does the amount of wire increase the magnetism?
3.) Is the nail really neccasary? Does it serve any other purpose than keeping the wire orderly?
4.) Does the voltage affect the magnetism?
Reply 12 years ago on Introduction
The gauge of the wire effects the resistance in the wire. lower gauge - less resistance.
A longer wire will have more resistance than a short one. A higher resistance in the wire, will limit the amount of current able to pass through.
A longer wire will make you able to do more turns, which makes the magnetism stronger.
Somewhere in there is a trade off as Betelgeus mentions.
The nail increases the magnetism, aswell as it will 'define' or make the magnetic field more focused if you will. The amount of voltage applied decides the amount of current. The amount of current and number of turns are important for the magnetic fields. More current and/or more turns makes it stronger.
current = voltage / resistance.
Reply 12 years ago on Introduction
The voltage is mostly what affects the magnetic field power. The nail (best if iron) does increase the magnetism dramatically, as iron is a ferrous (highly magnetic) material. There's a point where the length of the wire is optimal for the voltage being used, before that there's not enough wire to create an optimal field, and any longer and you would loose voltage to resistance and cross-inductance. The same applies to the gauge.
However, if you go and try to use a 9 volt with this setup, the amount of wire shown in the instructable is likely to short out and heat up very quickly.
13 years ago on Introduction
1. That looks like uninsulated copper wire there, what you will end up doing is creating a short circuit that will get very hot. You need to use insulated wire. Also, you should try a longer piece of wire, You will get a stronger magnet this way and less heat. 2. If you bring this near a CRT monitor it won't knock out your whole computer. If you bring it near an LCD (flatscreen) it's likely that nothing will happen at all.
Reply 12 years ago on Introduction
It's most likely enameled wire aka "magnet wire", it only look insulated. You will want to remember to strip the ends or heat them up enough (soldering iron can be good enough) to make sure you will have electric contact for your battery.
The magnet should work even if those wires aren't perfectly touching the nail. The current through the wire cause a magnetic field with a focus in the center of the loops. The nail enhance this magnetic field and giving you a defined North and South pole.
13 years ago on Introduction
mine doesn't work?
i used copper wire and a nail and i have tried numerous batteries
it looks just like this one
please help
Reply 12 years ago on Introduction
the nail may be galvanised and galvanised nails take away the voltage
Reply 13 years ago on Introduction
You may have used insulated wire, in which case you may need to sand the protective varnish off each end to make contact.
13 years ago on Introduction
Where did you get all those facts from because they are complete nonsense apart from causing some divergence on the screen.
14 years ago on Step 2
yes, but how strong is it?
Reply 14 years ago on Step 2
its probably not that strong but it depends on how much voltage and times u wrap the wiring around.
Reply 13 years ago on Step 2
for me i did this in school aswell and didnt think to post an instrucable, grrr for beating me to it... it depended on the size of my battery. i had a big one like the ones you put in flashlights and it worked REALLY well.
14 years ago on Introduction
nice, but if you accidently turn your monitor purple, all you need to do is push the degauss button, or reboot your monitor.
14 years ago on Introduction
I finished- you can publish now- but, hey- how come some on the list only have the instructables? Hey, and arent you the guy who puts naruto shippuden online- or does he just have the same user name, but on a different website?
Reply 14 years ago on Introduction
I forgot hand after instructables