Knex Monstertruck




Introduction: Knex Monstertruck

This is my knex monstertruck that i made a few years ago and was going to post on my old acccount but never got around to it. So now i have some spare time i will post. First off it has suspension (although it is prone to breaking if dropped), working stearing and the bonnet copens to reveal an engine(just for show). The doors can open and a knex man can fit inside but this is mainly model is mainly for show.

These pictures are quite old so some may be missing or be bad photos.

So here are the pics so get making!!

And be sure to rate, comment, subscribe and be sure to check out my other creations.

Step 1: Base

This is the base and suspension

1-make this
7-attach 1 to 2
8-attach 4 to 7
9-attach 6 to 8

(make 2)
10,11,12-make these
13-attach 11 to 12
14,15-attach 10 to 13
16,17,18-add this

19,20,21-add the lacky band here

22,23,24,25,26-add wheel


29-a full picture of the steering
30,31-better pictures of rear (or front if you dont want it to turn)

Step 2: Chassis Rear

1,2,3,4,5,6-make these
7-attach 3 to 5
8-attach 4 to 5
9-attach 1 to 8
10-attach 2 to 9
12-attach 6 to 10

Step 3: Chassis Front

This is the longest and hardest step. Try to follow the pictures although they aren't too clear.

2-attach parts from 1
3,4,5,6,7-try to make whats in the pictures

8,9,10,11,12,13-make these
14-attach 9 to 13
15,16-attach 8 to 14
17-attach 11 to 16 (repeat for other side)

20-attach 18 to 19

21-attach 9
22-attach 20 and 7 to 17(sorry but this is the best picture i found)

Step 4: Roof

1,2,3,4-make these
5-attach 1 to 2
6-attach 3 to 4
7-attach 5 to 6

Step 5: Assembly

1,2,3-connect front to rear
4-attach top
5,6-attach chassis to base

now you should be finished and if you need any help please message me.

Be the First to Share


    • Knitting and Crochet Speed Challenge

      Knitting and Crochet Speed Challenge
    • One Board Contest

      One Board Contest
    • Raspberry Pi Contest

      Raspberry Pi Contest



    10 years ago on Introduction

    Epic! I made this and had a derby with my friend and mine only broke once and it was a quick fix. Very sturdy


    10 years ago on Introduction

    AWESOME! That monster truck is very strong, big, and cool! Great job!

    great job. the looks are good, but im even more impressed by the suspension and the creativity and neatness. 5* keep up the good work


    10 years ago on Introduction

    Tried making it, but couldn't get the suspension to work properly, so gave up

    White Shadow
    White Shadow

    Reply 10 years ago on Introduction

    Sorry the pictures are a bit hard to follow but if u look at them carefully then you should be able to make it.


    Reply 10 years ago on Introduction

    I had the whole of the chassis built, but when i pushed down on it, the suspension didn't work as the top bit and bottom parts just pushed against each other :/

    White Shadow
    White Shadow

    Reply 10 years ago on Introduction

    Well i havnt had this built fotr well over 2 years so i cant realy check whats happening. Just remake the suspension again and sorry i couldnt help much.


    10 years ago on Introduction

    put a 3-barreled Gatling gun with 2 triangular shields attached on the back & BAM! you have a halo warthog